Woodstock W1677, W1711 owner manual Resawing Operations, Components Needed for Resawing

Page 37

W1677/W1711 10" Table Saw

Resawing Operations

Resawing pushes a table saw to its limits. If the motor bogs down when resawing, slow down your feed rate. Also, use a ripping blade when resawing to reduce motor overloading and blade wear. Ripping blades are designed to clear the sawdust quickly.

Components Needed for Resawing:

 

Zero Clearance Insert

1

Ripping Blade 10"

1

Clamps

2

Shop Made Auxiliary Fence

1

Shop Made Resaw Barrier

1

To perform resawing operations, do these steps:

 

1.DISCONNECT THE SAW FROM POWER!

2.Remove the table insert and the blade guard/split- ter, install a ripping blade and a zero clearance table insert, and lower the blade below the table surface.

3.Attach the auxiliary fence to the standard fence and set it to the desired width. Note: Account for blade kerf, the rough cut made by the blade, and the inaccuracy of the fence scale when the auxil- iary fence is installed when figuring out the correct width.

4.Place the workpiece against the fence, slide the resaw barrier against the workpiece, and clamp the resaw barrier to the table top (see Figure 55).

5.Slide the workpiece over the blade to make sure it moves smoothly.

6.Raise the blade approximately an inch, or close to half the height of the workpiece, whichever is less.

7.Plug in the table saw, turn it ON, and use a push stick to feed the workpiece through the blade using a slow, steady feed rate.

8.Flip the workpiece end for end, keeping the same side against the fence, and run the workpiece through the blade.

9.Turn OFF the table saw, then separate the parts of the workpiece and hand plane the remaining ridge.

10.When finished resawing, remove the resaw barrier and re-install the blade guard/splitter.

-35-

You may experience kickback during this procedure. Stand to the side of the blade and wear a full face shield to pre- vent injury when resawing.

Always use push sticks or push paddles to increase safety and control during operations which require that the blade guard and splitter be removed from the saw. ALWAYS replace the blade guard after resawing is complete.

The danger of kickback increases rela- tive to the depth of a cut. Reduce the risk of kickback by making multiple passes to achieve the desired depth of cut. Failure to follow these warnings could result in serious personal injury.

���������

���������

 

 

�����

�����

������������

���������������

Figure 55. Completed resaw cut.

OPERATIONS

Page 36 Page 38
Image 37
Page 36 Page 38
Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms 220V Operation ElectricalExtension Cords GroundingUnpacking SetupInventory Box Inventory Figures 12 QtyInventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementMobile Base AssemblyTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Before you test run the machine, do these steps Test RunTo test run the table saw, do these steps General OperationsBlade Height Feed RateBlade Material Blade SelectionBlade Types To change blades, do these steps Changing BladesThrough Cuts Through vs. Non-Through CutsNon-Through Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these stepsCross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these stepsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsComponents Needed for the Auxiliary Fence Auxiliary FenceTo build the auxiliary fence, do these steps Components Needed for Resawing Resawing OperationsTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesCleaning MaintenanceBelts Table & BaseBlade Tilt Stop Bolts ServiceTo set the stop bolts on the trunnion, do these steps To adjust the geared bearing housing, do these steps To adjust the trunnion assembly, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentMiter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsReplacing V-Belts Adjusting FenceTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents