Woodstock W1711, W1677 owner manual Test Run, Before you test run the machine, do these steps

Page 24

W1677/W1711 10" Table Saw

Test Run

SETUP

Before you test run the machine, do these steps:

1.Read all the warnings and directions regarding the operation and controls of this machine.

2.Make sure the saw is stable.

3.Make sure the blade is mounted correctly and that the arbor nut is tight.

4.Make sure the fence is parallel to the blade.

5.Make sure the guard assembly is installed, aligned with the blade, and functional.

6.Make sure the saw blade does not touch the table insert when it is adjusted to the maximum tilt angle and height.

To test run the table saw, do these steps:

1.Connect the table saw to the power source.

2.Face the table saw and stand to the left of the blade path.

3.Turn the table saw ON.

—The table saw should run smoothly with little or no vibration; once it does, the machine is ready for regular operations.

—Immediately turn the table saw OFF if you suspect any problems, and refer to Page 48 to trouble- shoot/fix any problems before starting the table saw again. (If the source of an unusual noise or vibration is not readily apparent, contact our technical support for help.)

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses during assembly and operation.

Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery.

-22-

Image 24

Contents LEFT-TILT Table SAW Page Table of Contents Introduction Woodstock Technical SupportW1677 Series Specifications W1711 Series Specifications Controls and Features Fence controls Blade Guard/Splitter Miter GaugeSafety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Avoiding Potential Injuries Unplug saw before changing bladesUse featherboards when possible To protect against kickback Kickback Use a zero-clearance table insert whenever possibleCommon Terms Electrical 220V OperationExtension Cords GroundingSetup UnpackingInventory Box Inventory Figures 12 QtyShop Fox Classic Fence Inventory Inventory Needed for Your SawStandard Rails Figure Qty Long Rails Figure QtyShop Fox Original Fence Inventory Flat Washers 3⁄ 8 Rail/Ext TableMachine Placement Cleaning MachineAssembly Mobile BaseTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Test Run Before you test run the machine, do these stepsTo test run the table saw, do these steps Operations GeneralBlade Height Feed RateBlade Selection Blade MaterialBlade Types Changing Blades To change blades, do these stepsThrough vs. Non-Through Cuts Through CutsNon-Through Cuts When using the tilting mechanism Rip CutsBlade Tilt/Bevel Cuts To make a rip cut, do these stepsTo crosscut using the miter gauge, do these steps Cross CutsMiter Cuts To cut a miter, do these stepsDado Cuts To use a stacked or wobble dado blade, do these stepsFirst cut when making a dado With a standard ripping blade To cut dadoes with a standard blade, do these stepsRabbet Cuts To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps Clearly mark the width of the rabbet cut on WorkpieceResawing Resaw BarrierComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsAuxiliary Fence Components Needed for the Auxiliary FenceTo build the auxiliary fence, do these steps Resawing Operations Components Needed for ResawingTo perform resawing operations, do these steps Aftermarket Safety Accessories Outfeed roller tableShop-Made Safety Accessories Here are some of the basic items you may want to considerMaintenance CleaningBelts Table & BaseService Blade Tilt Stop BoltsTo set the stop bolts on the trunnion, do these steps To adjust the trunnion assembly, do these steps To adjust the geared bearing housing, do these stepsBlade Alignment Miter Slot Parallel to Blade Measuring blade to miter slotShimming Wings To shim an extension wing, do these stepsSplitter Adjustment To check and align the splitter to the blade, do these stepsAngle Pointer Miter GaugeTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsAdjusting Fence Replacing V-BeltsTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Troubleshooting Motor & ElectricalTable Saw Operations Possible Cause Corrective ActionParts Table/Body BreakdownPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA