Woodstock W1677, W1711 owner manual Always Lock Mobile Bases if Used Before Operating Machinery

Page 9

W1677/W1711 10" Table Saw

10.NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended.

11.DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist.

12.KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.

13.USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over- heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords for 220V machinery.

14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is in OFF position before reconnecting.

15.MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

16.MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.

17.REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting wrenches before turning machinery ON.

18.CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine operation. Repair or replace damaged parts.

19.USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury.

20.DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.

21.SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured workpiece protects your hands and frees both hands to operate the machine.

22.DO NOT OVERREACH. Keep proper footing and balance at all times.

23.MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi- tions that cause the workpiece to "kickback."

24.ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.

25.BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and animals, especially fine dust. Make sure you know the hazards associated with the type of dust you will be exposed to and always wear a respirator approved for that type of dust.

-7-

SAFETY

Image 9

Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms 220V Operation ElectricalExtension Cords GroundingUnpacking SetupInventory Box Inventory Figures 12 QtyInventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementAssembly Mobile BaseTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Test Run Before you test run the machine, do these stepsTo test run the table saw, do these steps General OperationsBlade Height Feed RateBlade Selection Blade MaterialBlade Types To change blades, do these steps Changing BladesThrough vs. Non-Through Cuts Through CutsNon-Through Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these stepsCross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these stepsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsAuxiliary Fence Components Needed for the Auxiliary FenceTo build the auxiliary fence, do these steps Resawing Operations Components Needed for ResawingTo perform resawing operations, do these steps Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesCleaning MaintenanceBelts Table & BaseService Blade Tilt Stop BoltsTo set the stop bolts on the trunnion, do these steps To adjust the trunnion assembly, do these steps To adjust the geared bearing housing, do these stepsBlade Alignment Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentMiter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsAdjusting Fence Replacing V-BeltsTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA