Woodstock W1711, W1677 owner manual To cut rabbets with the standard blade, do these steps

Page 34

OPERATIONS

W1677/W1711 10" Table Saw

Cutting rabbets with a standard saw blade DOES NOT

require the use of a sacrificial fence. Reduce motor over-

��

loading and blade wear by using a ripping blade. Ripping

��

blades are designed to clear the sawdust quickly.

To cut rabbets with the standard blade, do these steps:

��

1. DISCONNECT THE SAW FROM POWER!

2. Clearly mark the width of the rabbet cut on the

workpiece.

Note: Include marks on the edge of the workpiece

to clearly identify the intended cut while it is laying

flat on the saw table.

Figure 50. First cut when rabbet cutting

with a standard rip blade.

3.Raise the blade up to the desired depth of cut

(depth of rabbet channel desired). When cutting

deep rabbets, take more than one pass to reduce

��

the risk of kickback.

��

4. Adjust the fence so the blade is aligned with the

inside of your rabbet channel as shown in Figure 50.

5. Stand the workpiece on edge as shown in Figure 51,

and adjust the saw blade height to intersect with

��

the first cut.

6. Perform the second cut to complete the rabbet.

Figure 51. Second cut when rabbet cutting

with a standard rip blade.

-32-

Image 34

Contents LEFT-TILT Table SAW Page Table of Contents Introduction Woodstock Technical SupportW1677 Series Specifications W1711 Series Specifications Controls and Features Fence controls Blade Guard/Splitter Miter GaugeSafety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Avoiding Potential Injuries Unplug saw before changing bladesUse featherboards when possible To protect against kickback Kickback Use a zero-clearance table insert whenever possibleCommon Terms Extension Cords Electrical220V Operation GroundingInventory SetupUnpacking Box Inventory Figures 12 QtyStandard Rails Figure Qty Shop Fox Classic Fence InventoryInventory Needed for Your Saw Long Rails Figure QtyShop Fox Original Fence Inventory Flat Washers 3⁄ 8 Rail/Ext TableMachine Placement Cleaning MachineMobile Base AssemblyTo assemble your table saw, do these steps Motor shipping brace Installing blade Adjusting table insert flush Before you test run the machine, do these steps Test RunTo test run the table saw, do these steps Blade Height OperationsGeneral Feed RateBlade Material Blade SelectionBlade Types Changing Blades To change blades, do these stepsThrough Cuts Through vs. Non-Through CutsNon-Through Cuts Blade Tilt/Bevel Cuts When using the tilting mechanismRip Cuts To make a rip cut, do these stepsMiter Cuts To crosscut using the miter gauge, do these stepsCross Cuts To cut a miter, do these stepsDado Cuts To use a stacked or wobble dado blade, do these stepsFirst cut when making a dado With a standard ripping blade To cut dadoes with a standard blade, do these stepsRabbet Cuts To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps Clearly mark the width of the rabbet cut on WorkpieceComponents Needed for the Resaw Barrier ResawingResaw Barrier To build the resaw barrier, do these stepsComponents Needed for the Auxiliary Fence Auxiliary FenceTo build the auxiliary fence, do these steps Components Needed for Resawing Resawing OperationsTo perform resawing operations, do these steps Aftermarket Safety Accessories Outfeed roller tableShop-Made Safety Accessories Here are some of the basic items you may want to considerBelts MaintenanceCleaning Table & BaseBlade Tilt Stop Bolts ServiceTo set the stop bolts on the trunnion, do these steps To adjust the geared bearing housing, do these steps To adjust the trunnion assembly, do these stepsBlade Alignment Miter Slot Parallel to Blade Measuring blade to miter slotShimming Wings To shim an extension wing, do these stepsSplitter Adjustment To check and align the splitter to the blade, do these stepsTo set the angle pointer, do these steps Angle PointerMiter Gauge To set the miter gauge pointer, do these stepsReplacing V-Belts Adjusting FenceTo replace the V-belts, do these steps W1677 Wiring Diagram W1711 Wiring Diagram Troubleshooting Motor & ElectricalTable Saw Operations Possible Cause Corrective ActionParts Table/Body BreakdownPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA