Woodstock W1677, W1711 Replacing V-Belts, Adjusting Fence, To replace the V-belts, do these steps

Page 47

W1677/W1711 10" Table Saw

Replacing V-Belts

The V-belts are tensioned by pivoting the motor up or down. The slotted holes in the motor mount bracket (Figure 76) allow the motor to pivot in the hinge holes.

To replace the V-belts, do these steps:

1.DISCONNECT SAW FROM POWER SOURCE!

2.Loosen the motor mount bolts.

3.Pivot the motor up so the belts loosen, then remove them from the pulleys.

4.Install a matching set of new V-belts.

5.Pivot the motor down to tighten the belts, and hold downward pressure on the motor with one hand and tighten the motor mount bolts with the other hand.

6.Check the belt tension by pushing (with moderate pressure) one of the belts between the pulleys, as shown in Figure 77. The correct deflection range is between 1⁄4" and 1⁄2".

Note: V-belts only need to be tight enough so they don't slip when the motor is at full load. Extremely tight V-belts will cause the motor and pulley bear- ings to wear faster.

Adjusting Fence

The adjustment set screws shown in Figure 78 allow you to pivot the fence left or right to make it parallel with the blade. The fence must be parallel to the blade or slightly (no more than 1⁄32" from front to back) angled away from the blade at the rear of the fence so the workpiece will not bind between the fence and blade during the cut.

If your workpiece binds as you make your cuts, the risk of serious personal injury from kickback increases dra- matically. Signs that the workpiece is binding include burn marks on the workpiece and difficulty feeding the workpiece completely through the cut.

The basic procedure for adjusting the fence is to tighten one side and loosen the other side in equal increments. The side that is loosened is the side that the fence will move toward. For full instructions on adjusting the fence, refer to the Owner's Manual included with the fence.

-45-

�������������

�����������

Figure 76. Motor mount anatomy.

������

����������

������

Figure 77. Checking V-belt deflection to

ensure correct tension.

 

Close Up View

 

of Adjustment

 

Mechanism

Adjustment

SERVICE

 

Set Screws

 

Figure 78. Fence adjustment controls.

Page 46 Page 48
Image 47
Page 46 Page 48
Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms Grounding Electrical220V Operation Extension CordsBox Inventory Figures 12 Qty SetupUnpacking InventoryLong Rails Figure Qty Shop Fox Classic Fence InventoryInventory Needed for Your Saw Standard Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementTo assemble your table saw, do these steps AssemblyMobile Base Motor shipping brace Installing blade Adjusting table insert flush To test run the table saw, do these steps Test RunBefore you test run the machine, do these steps Feed Rate OperationsGeneral Blade HeightBlade Types Blade SelectionBlade Material To change blades, do these steps Changing BladesNon-Through Cuts Through vs. Non-Through CutsThrough Cuts To make a rip cut, do these steps When using the tilting mechanismRip Cuts Blade Tilt/Bevel CutsTo cut a miter, do these steps To crosscut using the miter gauge, do these stepsCross Cuts Miter CutsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsTo build the resaw barrier, do these steps ResawingResaw Barrier Components Needed for the Resaw BarrierTo build the auxiliary fence, do these steps Auxiliary FenceComponents Needed for the Auxiliary Fence To perform resawing operations, do these steps Resawing OperationsComponents Needed for Resawing Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesTable & Base MaintenanceCleaning BeltsTo set the stop bolts on the trunnion, do these steps ServiceBlade Tilt Stop Bolts Blade Alignment To adjust the trunnion assembly, do these stepsTo adjust the geared bearing housing, do these steps Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentTo set the miter gauge pointer, do these steps Angle PointerMiter Gauge To set the angle pointer, do these stepsTo replace the V-belts, do these steps Adjusting FenceReplacing V-Belts W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA
Top Page Image Contents