Woodstock W1711 owner manual W1677 Series Specifications

Page 5

W1677/W1711 10" Table Saw

W1677 Series Specifications

Model Number	W1677	W1677EXT1	W1677EXT2

Motor	3 HP	3 HP	3 HP

Voltage	220V	220V	220V

Phase	Single-Phase	Single-Phase	Single-Phase

Amps	18	18	18

Speed	3450 RPM	3450 RPM	3450 RPM

Table Size (full assembly)	401⁄8" x 27"	841⁄8" x 27"	841⁄8" x 27"
Table Height	34"	34"	34"
Overall Machine Size	56"L x 34"W	84"L x 34"W	84"L x 34"W
Footprint Size	201⁄2"L x 201⁄2"W	201⁄2"L x 201⁄2"W	201⁄2"L x 201⁄2"W
Weight	410 lbs.	500 lbs.	500 lbs.

Fence	Shop Fox Classic	Shop Fox Classic	Shop Fox Original

Long Rails & Extension Table	No	Yes	Yes


Maximum Rip Right of Blade	26"	52"	49"
Maximum Rip Left of Blade	8"	8"	8"
Maximum Depth of Cut at 90°	3"	3"	3"
Maximum Depth of Cut at 45°	21⁄8"	21⁄8"	21⁄8"

Maximum Blade Diameter	10"	10"	10"

Arbor Size	5⁄8"	5⁄8"	5⁄8"
Arbor Speed	4200 RPM	4200 RPM	4200 RPM

Rim Speed	11,000 FPM	11,000 FPM	11,000 FPM

Blade Tilt (Left)	0° – 45°	0° – 45°	0° – 45°

Maximum Dado Width	13⁄16"	13⁄16"	13⁄16"

Miter Slot Size	3⁄4"W x 3⁄8"H	3⁄4"W x 3⁄8"H	3⁄4"W x 3⁄8"H
Dust Port Size	4"	4"	4"
Country of Origin	Taiwan	Taiwan	Taiwan
Assembly Time (approx.)	60 Minutes	90 Minutes	90 Minutes

Warranty	2 Year	2 Year	2 Year

INTRODUCTION

-3-

Image 5

Contents LEFT-TILT Table SAW Page Table of Contents Woodstock Technical Support IntroductionW1677 Series Specifications W1711 Series Specifications Fence controls Blade Guard/Splitter Miter Gauge Controls and FeaturesStandard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Specific Safety Instructions for Table Saws Unplug saw before changing blades Avoiding Potential InjuriesUse featherboards when possible To protect against kickback Use a zero-clearance table insert whenever possible KickbackCommon Terms 220V Operation ElectricalExtension Cords GroundingUnpacking SetupInventory Box Inventory Figures 12 QtyInventory Needed for Your Saw Shop Fox Classic Fence InventoryStandard Rails Figure Qty Long Rails Figure QtyFlat Washers 3⁄ 8 Rail/Ext Table Shop Fox Original Fence InventoryCleaning Machine Machine PlacementTo assemble your table saw, do these steps AssemblyMobile Base Motor shipping brace Installing blade Adjusting table insert flush To test run the table saw, do these steps Test RunBefore you test run the machine, do these steps General OperationsBlade Height Feed RateBlade Types Blade SelectionBlade Material To change blades, do these steps Changing BladesNon-Through Cuts Through vs. Non-Through CutsThrough Cuts Rip Cuts When using the tilting mechanismBlade Tilt/Bevel Cuts To make a rip cut, do these stepsCross Cuts To crosscut using the miter gauge, do these stepsMiter Cuts To cut a miter, do these stepsTo use a stacked or wobble dado blade, do these steps Dado CutsTo cut dadoes with a standard blade, do these steps First cut when making a dado With a standard ripping bladeTo cut rabbets with the dado blade, do these steps Rabbet CutsClearly mark the width of the rabbet cut on Workpiece To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingComponents Needed for the Resaw Barrier To build the resaw barrier, do these stepsTo build the auxiliary fence, do these steps Auxiliary FenceComponents Needed for the Auxiliary Fence To perform resawing operations, do these steps Resawing OperationsComponents Needed for Resawing Outfeed roller table Aftermarket Safety AccessoriesHere are some of the basic items you may want to consider Shop-Made Safety AccessoriesCleaning MaintenanceBelts Table & BaseTo set the stop bolts on the trunnion, do these steps ServiceBlade Tilt Stop Bolts Blade Alignment To adjust the trunnion assembly, do these stepsTo adjust the geared bearing housing, do these steps Measuring blade to miter slot Miter Slot Parallel to BladeTo shim an extension wing, do these steps Shimming WingsTo check and align the splitter to the blade, do these steps Splitter AdjustmentMiter Gauge Angle PointerTo set the angle pointer, do these steps To set the miter gauge pointer, do these stepsTo replace the V-belts, do these steps Adjusting FenceReplacing V-Belts W1677 Wiring Diagram W1711 Wiring Diagram Motor & Electrical TroubleshootingPossible Cause Corrective Action Table Saw OperationsTable/Body Breakdown PartsPART# Description Motor/Trunnion Breakdown Handwheellock Guard/Miter Gauge Breakdown XPB15 Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA