Bostitch 500 SERIES DIAL-A-DEPTH Fastener Control Adjustment, To Prevent Accidental Injuries

Page 6

LOADING THE 400 & 500

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

•Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

•Never point the tool at anyone else.

•Never engage in horseplay.

•Never pull the trigger unless nose is directed at the work.

•Always handle the tool with care.

•Do not pull the trigger or depress the trip mechanism while loading the tool.

A

B

1.Move pusher to rear until latched. Cover will open. Pusher front will drop into notch on top of magazine assembly.

2.Drop staple stick over magazine and slide forward. Repeat until magazine is loaded, allowing enough space for pusher to disengage the magazine and the cover to close. Approximately 1/2" (13mm)

3.Pull and hold top part of knob

(A)and depress bottom part of knob (B) in a clockwise direction to release pusher.

NOTE: Use only staples recommended by Bostitch for the 400 & 500 Series staplers or staples which meet BOSTITCH specifications.

Always disconnect air supply: 1. Before making adjustments; 2. When servicing the tool;

3.When clearing a jam; 4. When tool is not in use; 5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.

“DIAL-A-DEPTH™” FASTENER CONTROL ADJUSTMENT

The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth; from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in the specific work as described on page 5, then use the DIAL-A-DEPTH™ Fastener Control adjustment to give the desired depth of drive.

TO ADJUST DIAL-A DEPTH™ FASTENER CONTROL ADJUSTMENT:

1.With air pressure set (refer to Setting the Correct Pressure on (Page 5), drive a few fasteners into a representative material sample to determine if adjustment is necessary.

2.If adjustment is required, disconnnect air supply.

3.Refer to label on outside of door for direction to turn adjusting nut. (See illustration)

4.Open trip cover and turn adjusting nut as shown to set the desired fastener countersink depth.

5.Close cover. Before reconnecting air supply, check that trip mechanism parts operate freely with no binding or sticking.

6.Reconnect air supply.

-6-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 400 & 500 Series Introduction IndexLoading Tool Safety InstructionsAIR Supply and Connections Operation400 & 500 Series Tool Specifications Lubrication DIAL-A-DEPTH Fastener Control Adjustment To Adjust DIAL-A Depth Fastener Control AdjustmentTo Prevent Accidental Injuries Trigger Operation Tool OperationBefore Handling or Operating this Tool Contact Trip OperationTool Must not Cycle Tool Operation CheckTrigger Operated Tool Tool Must CycleAIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintaining the Pneumatic ToolTrouble Shooting Power Adjustment ValveProblem Cause Correction Quick Release Magazine Accessories AvailableDirectional Exhaust Deflector Recommended ToolsIntroducción ÍndiceNota AL Cargar LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones OperaciónEspecificaciones DE LAS Herramientas 400 Y Lubricación Cómo Cargar EL 400 Y Advertencia Para Impedir Lesiones AccidentalesOperación POR GA Tillo Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disp ARO POR ContactoOperación POR Disp ARO Secuencial Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo LA Herramienta no Debe Efectuar SU CicloPartes DE Reemplazo Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamble Para LOS SellosCausa Corrección ProblemaDiagnóstico DE Falla Para Obtener Máxima PotenciaAccesorios Disponibles Deflector DE Escape DireccionalCargador DE Desenganche Rápido Herramientas RecomendadasSommaire RemarqueChargement DE L’APPAREIL Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement FonctionnementCaractéristiques DU 400/500 OpérationLubrification Chargement DU 400/500 Réglage DU Calibre DIAL-A-DEPTH DE LagrafeusePour Prévenir UN Accident Mode D’EMPLOI Fonctionnement DE L’APPAREILSystème DE Sécurité À LA Volée C.T Vérification DU Système DE DéclenchementDéclenchement P AR LA Détente Système DE Sécurité AU COUP-PAR-COUPAlimentation D’AIR Pression Volume Pièces DE RechangeProcédure D’ASSEMBLAGE DES Garnitures Problèmes DE Fonctionnement Vanne DE Réglage DE PuissanceProblème Cause Correction Déflecteur D’ÉCHAPPEMENT Directionnel Accessoires OffertsOutils Recommandés Chargeur À Déclenchement Rapide

400 SERIES, 500 SERIES specifications

The Bostitch 500 Series and 400 Series are two lines of pneumatic nailers and staplers renowned for their robust performance and innovative features in the construction and woodworking industries. Designed to enhance efficiency and precision, these tools are ideal for both professional and DIY applications.

The Bostitch 500 Series is known for its versatile functionality and lightweight construction. It includes a range of models that cater to framing, roofing, and finishing tasks. One of its standout features is the integrated tool-free depth adjustment that allows users to easily set the desired nail depth without the need for additional tools. This ensures consistent results across various materials, such as softwood, hardwood, and engineered wood.

Another significant technology present in the 500 Series is the oil-free design, which reduces maintenance time and the risk of oil stains on work surfaces. Additionally, these nailers are equipped with a selectable trigger system that allows users to switch between sequential and bump firing modes. This flexibility enables operators to adapt to different work requirements efficiently.

The 400 Series, on the other hand, is specifically designed for heavy-duty applications, making it perfect for professional contractors. These models feature a more robust build quality and enhanced durability, capable of handling tougher jobs with ease. The 400 Series also boasts a high-capacity magazine that minimizes downtime for reloading, allowing for continuous operation on larger projects.

In terms of technological advancements, the 400 Series incorporates an advanced anti-dry fire mechanism that prevents the tool from firing when there are insufficient fasteners in the magazine. This feature not only protects the work surface but also prolongs the lifespan of the tool. Additionally, the lightweight design ensures that users can maneuver the tool comfortably, reducing fatigue during prolonged use.

Both series feature Bostitch’s signature design elements, including ergonomic handles for better grip and comfort, and a compact profile for easy access in tight spaces. The durable construction of each model ensures that they can withstand the rigors of daily use on the job site.

In summary, the Bostitch 500 Series and 400 Series offer a blend of cutting-edge technology, user-friendly features, and durable construction, making them essential tools for professionals and enthusiasts alike. With their efficient performance and innovative designs, these nailers and staplers continue to set the standard in the industry.
Top Page Image Contents