Multiquip EHTX44Y5 operation manual 25 20

Page 18

26 27

24

CONTROLS AND INDICATORS

25 20 28

29

29

30

31	23	22	21
31

Figure 3. EHTX Controls and Components (Rear)

20.Documentation Box – Storage for documentation and other information regarding the trowel.

21.Battery – Provides +12V DC power to the electrical system.

22.Hydraulic Oil Sight Glass – Indicates the level of the hydraulic oil in the reservoir.

23.Hydraulic Suction Filter – Filters hydraulic fluid prior to entering the system. (10 Micron absolute synthetic media.)

24.Hydraulic Oil Expansion Tank – Accommodates expanding hydraulic oil as it gets hot. The oil gravity flows back to the reservoir as it cools down, therefore NEVER open the the Hydraulic Oil Filler Cap (Item 30) when the system is warm and the oil has expanded.

25.Steering Control (Left Side) – Allows the unit to move in a forward or reverse direction only.

26.Blade Pitch Control Switch (Left Side) – Adjusts the left side blade pitch independently of the right side.

27.Blade Pitch Control (Twin Pitch)™ – Adjusts the blade pitches simultaneously.

28.Steering Control (Right Side) – Allows the unit to move in either a forward, reverse left or right direction.

29.Grill Guards (Left and Right) – Protects operator from moving components. Remove for maintenance access.

30.Hydraulic Oil Filler Cap – Remove this cap to add hydraulic oil. Open ONLY when system is cooled down and all expanded oil has returned to the reservoir.

31.Retardant Spray Tank – Holds 5 gallons of retardant, water, or other liquid.

WARNING

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating. NEVER operate the engine with the muffler removed.

page 18 — eHtx44y RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13)

Image 18

Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Silicosis Warning Respiratory HazardsEhtx Ride-On Trowel Page Training checklist CompletelyDaily pre-operation checklist Burn hazards SaFeTy meSSageSExplosive fuel hazards Rotating parts hazardsGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipmentFueL SaFeTy BaTTeRy SaFeTy„ Use well-insulated gloves when picking up the battery TRaNSpORTINg SaFeTy „ NeveR lift trowel with the operator on the machine„ aLWayS shutdown engine before transporting Emission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeDIMENSIONS/SPECIFICATIONS EhtxGuaranteed ISO 37442010 Based SpecificationsGuaranteed ISO 112012010 Based Sound Power Level in dBA bGeneral Information Controls and Indicators Hour Meter Indicates number of hours machine has been used25 20 Engine Components Fuel Filter Removes dirt and water from the engine fuelSeat assembly SetupTrowel Setup Instructions Battery SetupEngine Oil Level InspectionHydrauic Oil Level FuelInsert the ignition key into the ignition switch, Figure OperationPlace the engine speed control lever, in the LOW position Steering Place the engine speed control lever, in the High positionTrowel Speed Limiter Control Blade Pitch ControlClean and remove any foreign debris from the trowe Engine Shut-DownMAINTENANCE Air Cleaner Remove the air cleaner elementOFF position Checking Engine Oil Daily Changing Engine Oil And FilterFilter element from the inside out Vol % Freezing Point Boiling Point Anti Operation in Freezing WeatherGal 9.5 liters 108 226Radiator Maintenance Fuel FilterFuel/Water Separator Oil And Fuel Lines Battery/Charging SystemCheck and clean battery terminals for corrosion Checking The V-BeltLeft Side Trowel Speed Adjustment Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Engine Tune-UpBlade Pitch Adjustment Procedure Blade Pitch Adjustment BoltStabilizer Ring Removal Changing BladesTrowel Arm Adjustment Spider RemovalPlace the trowel on a FLAT, Level surface Trowel Arm Removal Remove spider to hydraulic motor retainingscrewRemove the trowel arm from the spider plate Locate the trowel arm adjustment tool P/N Checking Trowel Arm StraightnessRe-Assembly Trowel Arm Adjustment Fixture ComponentsInstalling Pans Onto Finisher Blades Checking Hydraulic Steering PressureLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Steering Pressure Adjustment Checking Steering PressureCool Oil1 155-175 PSI Hot Oil 145-165 PSI Pitch Pressure Out of Specification Press the left pitch rocker switch downwardPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentWiring Diagram SWITCH,KEYHydraulic Diagram Troubleshooting Troubleshooting Ride-On Hydraulic TrowelWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help