Multiquip EHTX44Y5 operation manual Training checklist, Completely

Page 6

training checklist

TRAINING CHECKLIST

This checklist will list some of the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist whenever a new operator is to be trained or it can be used as a review for more experienced operators.

Training Checklist

No.

Description

OK?

Date

1Read operation manual

completely

		Machine layout, location of
	2	components, checking of engine
		and hydraulic oil levels

	3	Fuel system, refueling procedure

	4	Operation of spray and lights

	5	Operation of controls (machine
	5	not running)
		not running)

	6	Safety controls, safety stop switch
	6	operation
		operation
	7	Emergency stop procedures

	8	Startup of machine, pre-heat,
	8	engine choke
		engine choke

	9	Maintaining a hover

	10	Maneuvering

	11	Pitching

12Matching blade pitch. Twin-Pitch™

13Concrete fi nishing techniques

14Shutdown of machine

15Lifting of machine (lift loops)

16Machine transport and storage

page 6 — eHtx44y RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13)

Image 6

Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Silicosis Warning Respiratory HazardsEhtx Ride-On Trowel Page Training checklist CompletelyDaily pre-operation checklist Burn hazards SaFeTy meSSageSExplosive fuel hazards Rotating parts hazardsGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipmentFueL SaFeTy BaTTeRy SaFeTy„ Use well-insulated gloves when picking up the battery TRaNSpORTINg SaFeTy „ NeveR lift trowel with the operator on the machine„ aLWayS shutdown engine before transporting Emission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeDIMENSIONS/SPECIFICATIONS EhtxGuaranteed ISO 37442010 Based SpecificationsGuaranteed ISO 112012010 Based Sound Power Level in dBA bGeneral Information Controls and Indicators Hour Meter Indicates number of hours machine has been used25 20 Engine Components Fuel Filter Removes dirt and water from the engine fuelSeat assembly SetupTrowel Setup Instructions Battery SetupEngine Oil Level InspectionHydrauic Oil Level FuelInsert the ignition key into the ignition switch, Figure OperationPlace the engine speed control lever, in the LOW position Steering Place the engine speed control lever, in the High positionTrowel Speed Limiter Control Blade Pitch ControlClean and remove any foreign debris from the trowe Engine Shut-DownMAINTENANCE Air Cleaner Remove the air cleaner elementOFF position Checking Engine Oil Daily Changing Engine Oil And FilterFilter element from the inside out Vol % Freezing Point Boiling Point Anti Operation in Freezing WeatherGal 9.5 liters 108 226Radiator Maintenance Fuel FilterFuel/Water Separator Oil And Fuel Lines Battery/Charging SystemCheck and clean battery terminals for corrosion Checking The V-BeltLeft Side Trowel Speed Adjustment Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Engine Tune-UpBlade Pitch Adjustment Procedure Blade Pitch Adjustment BoltStabilizer Ring Removal Changing BladesTrowel Arm Adjustment Spider RemovalPlace the trowel on a FLAT, Level surface Trowel Arm Removal Remove spider to hydraulic motor retainingscrewRemove the trowel arm from the spider plate Locate the trowel arm adjustment tool P/N Checking Trowel Arm StraightnessRe-Assembly Trowel Arm Adjustment Fixture ComponentsInstalling Pans Onto Finisher Blades Checking Hydraulic Steering PressureLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Steering Pressure Adjustment Checking Steering PressureCool Oil1 155-175 PSI Hot Oil 145-165 PSI Pitch Pressure Out of Specification Press the left pitch rocker switch downwardPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentWiring Diagram SWITCH,KEYHydraulic Diagram Troubleshooting Troubleshooting Ride-On Hydraulic TrowelWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help