Multiquip EHTX44Y5 operation manual Troubleshooting engine

Page 48

 

 

TROUBLESHOOTING

 

 

 

 

 

 

 

 

 

Troubleshooting (engine)

 

 

Symptom

possible problem

 

Solution

 

 

 

 

 

No Fuel reaching injection pump?

 

Add fuel. Check entire fuel system.

 

 

 

 

 

Defective fuel pump?

 

Replace fuel pump.

 

 

 

 

 

Fuel fi lter clogged?

 

Replace fuel fi lter and clean tank.

 

 

 

 

 

Faulty fuel supply line?

 

Replace or repair fuel line.

 

 

 

 

 

Compression too low?

 

Check piston, cylinder and valves. Adjust or

 

 

repair per engine repair manual.

Engine will not start or start is delayed,

 

 

Fuel pump not working correctly?

 

Repair or replace fuel pump.

although engine can be turned over.

 

Oil pressure too low?

 

Check engine oil pressure.

 

 

 

Low starting temperature limit exceeded?

 

Comply with cold starting instructions and

 

 

proper oil viscosity.

 

 

 

 

 

 

 

 

Defective battery?

 

Charge or replace battery.

 

 

 

 

 

Air or water mixed in fuel system?

 

Check carefully for loosened fuel line

 

 

coupling, loose cap nut, etc.

 

 

 

 

 

 

 

 

Engine oil too thick?

 

Refi ll engine crankcase with correct type of

At low temperatures engine will not start.

 

oil for winter environment.

 

 

 

Defective battery?

 

Replace battery.

 

 

 

 

Engine fi res but stops soon as starter is

Fuel fi lter blocked?

 

Replace fuel fi lter.

 

 

 

Fuel supply blocked?

 

Check the entire fuel system.

switched off.

 

 

 

 

Defective fuel pump?

 

Replace fuel pump.

 

 

 

 

 

 

 

Fuel tank empty?

 

Add fuel.

 

 

 

 

Engine stops by itself during normal

Fuel fi lter blocked?

 

Replace fuel fi lter.

 

 

 

Defective fuel pump?

 

Replace fuel pump.

operation.

 

 

 

 

 

Mechanical oil pressure shutdown sensor

 

Add oil. Replace low oil shutdown sensor if

 

stops the engine due to low oil?

 

necessary.

 

Fuel tank empty?

 

Replace fuel fi lter.

 

Fuel fi lter clogged?

 

Replace fuel fi lter.

 

Fuel tank venting is inadequate?

 

Ensure that tank is adequately vented.

 

Leaks at pipe unions?

 

Check threaded pipe unions tape and tighten

 

 

unions a required.

 

 

 

Low engine power, output and speed.

 

 

 

Speed control lever does not remain in

 

See engine manual for corrective action.

 

 

 

selected position?

 

 

 

 

 

 

 

 

 

Engine oil level too full?

 

Correct engine oil level.

 

 

 

 

 

 

 

Use No. 2-D diesel fuel only. Check the fuel

 

Injection pump wear?

 

injection pump element and delivery valve

 

 

 

assembly and replace as necessary.

page 48 — eHtx44y RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13)

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Silicosis Warning Respiratory HazardsEhtx Ride-On Trowel Page Training checklist CompletelyDaily pre-operation checklist SaFeTy meSSageS Explosive fuel hazardsBurn hazards Rotating parts hazardsGeNeRaL SaFeTy TROWeL SaFeTy ENgINe SaFeTyOrder Form PT-160 Before servicing equipmentFueL SaFeTy BaTTeRy SaFeTy„ Use well-insulated gloves when picking up the battery TRaNSpORTINg SaFeTy „ NeveR lift trowel with the operator on the machine„ aLWayS shutdown engine before transporting ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINg EmISSIONS INFORmaTIONEmission Control Label Label must remain with the engine for its entire lifeDIMENSIONS/SPECIFICATIONS EhtxSpecifications Guaranteed ISO 112012010 BasedGuaranteed ISO 37442010 Based Sound Power Level in dBA bGeneral Information Controls and Indicators Hour Meter Indicates number of hours machine has been used25 20 Engine Components Fuel Filter Removes dirt and water from the engine fuelSetup Trowel Setup InstructionsSeat assembly Battery SetupInspection Hydrauic Oil LevelEngine Oil Level FuelInsert the ignition key into the ignition switch, Figure OperationPlace the engine speed control lever, in the LOW position Steering Place the engine speed control lever, in the High positionTrowel Speed Limiter Control Blade Pitch ControlClean and remove any foreign debris from the trowe Engine Shut-DownMAINTENANCE Air Cleaner Remove the air cleaner elementOFF position Checking Engine Oil Daily Changing Engine Oil And FilterFilter element from the inside out Operation in Freezing Weather Gal 9.5 litersVol % Freezing Point Boiling Point Anti 108 226Radiator Maintenance Fuel FilterFuel/Water Separator Battery/Charging System Check and clean battery terminals for corrosionOil And Fuel Lines Checking The V-BeltRight Side Trowel Speed Adjustment Checking/Adjusting Trowel SpeedLeft Side Trowel Speed Adjustment Engine Tune-UpBlade Pitch Adjustment Procedure Blade Pitch Adjustment BoltStabilizer Ring Removal Changing BladesTrowel Arm Adjustment Spider RemovalPlace the trowel on a FLAT, Level surface Trowel Arm Removal Remove spider to hydraulic motor retainingscrewRemove the trowel arm from the spider plate Locate the trowel arm adjustment tool P/N Checking Trowel Arm StraightnessRe-Assembly Trowel Arm Adjustment Fixture ComponentsInstalling Pans Onto Finisher Blades Checking Hydraulic Steering PressureLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Steering Pressure Adjustment Checking Steering PressureCool Oil1 155-175 PSI Hot Oil 145-165 PSI Pitch Pressure Out of Specification Press the left pitch rocker switch downwardPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentWiring Diagram SWITCH,KEYHydraulic Diagram Troubleshooting Troubleshooting Ride-On Hydraulic TrowelWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help
Top Page Image Contents