Multiquip EHTX44Y5 operation manual Air Cleaner, OFF position, Remove the air cleaner element

Page 27

mAINTENANCE

NOTICE

When performing any maintenance on the trowel or engine, follow all safety messages and rules for safe operation stated at the beginning of this manual

At the front of this manual there is a “Daily Pre-Operation Checklist”. Make copies of this checklist and use it on a daily basis

. WARNING

Accidental starts can cause severe injury or death.

ALWAYS place the ON/OFF switch in the

OFF position.

Disconnect and ground spark plug leads and disconnect negative battery cable from battery before servicing.

WARNING

Some maintenance operations may require the engine to be run. Ensure that the maintenance area is well ventilated. Exhaust contains poisonous carbon monoxide gas that can cause unconsciousness and may result in

DEATH

CAUTION

ALWAYS allow the engine to cool before servicing. NEVER attempt any maintenance work on a hot engine.

CAUTION

Certain maintenance operations or machineadjustments require specialized knowledge and skill. Attempting to perform maintenance operations or adjustments without the proper knowledge, skills ortraining could result in equipment damage or injury to personnel. If in doubt, consult your dealer.

Air Cleaner

CAUTION

Wear protective equipment such as approved safety glasses or face shields and dust masks or respirators when cleaning air filters with compressed air.

This Yanmar diesel engine is equipped with a replaceable, high-density paper air cleaner element (Figure 19). This air cleaner may have an inner element (option) that is used as a backup filter should the main element becomes damaged.

ARROW

MARK

(CASE)

MAIN PAPER
AIR CLEANER
ELEMENT	ARROW
	MARK
	(DUST PAN)
AIR CLEANER
CASE
INNER	DUST PAN
ELEMENT
(OPTION)
LATCH
	EVACUATOR
	VALVE

Figure 19. Air Cleaner Components

1.Check the air cleaner daily or before starting the engine.

2.Check for and correct heavy buildup of dirt and debris along with loose or damaged components.

3.Replace the element if it is found to be damaged, excessively dirty, or oily.

4.Release the latches located on either side of the air cleaner dust pan, and remove the dust pan.

5.Remove the air cleaner element.

NOTICE

Operating the engine with loose or damaged air cleaner components could allow unfiltered air into the engine causing premature wear and failure.

ehtx44y5 RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13) — page 27

Image 27

Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Respiratory Hazards Silicosis WarningEhtx Ride-On Trowel Page Completely Training checklistDaily pre-operation checklist Rotating parts hazards SaFeTy meSSageSExplosive fuel hazards Burn hazardsGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160FueL SaFeTy BaTTeRy SaFeTy„ Use well-insulated gloves when picking up the battery TRaNSpORTINg SaFeTy „ NeveR lift trowel with the operator on the machine„ aLWayS shutdown engine before transporting Label must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelEhtx DIMENSIONS/SPECIFICATIONSSound Power Level in dBA b SpecificationsGuaranteed ISO 112012010 Based Guaranteed ISO 37442010 BasedGeneral Information Hour Meter Indicates number of hours machine has been used Controls and Indicators25 20 Fuel Filter Removes dirt and water from the engine fuel Engine ComponentsBattery Setup SetupTrowel Setup Instructions Seat assemblyFuel InspectionHydrauic Oil Level Engine Oil LevelInsert the ignition key into the ignition switch, Figure OperationPlace the engine speed control lever, in the LOW position Place the engine speed control lever, in the High position SteeringBlade Pitch Control Trowel Speed Limiter ControlEngine Shut-Down Clean and remove any foreign debris from the troweMAINTENANCE Air Cleaner Remove the air cleaner elementOFF position Checking Engine Oil Daily Changing Engine Oil And FilterFilter element from the inside out 108 226 Operation in Freezing WeatherGal 9.5 liters Vol % Freezing Point Boiling Point AntiRadiator Maintenance Fuel FilterFuel/Water Separator Checking The V-Belt Battery/Charging SystemCheck and clean battery terminals for corrosion Oil And Fuel LinesEngine Tune-Up Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Left Side Trowel Speed AdjustmentBlade Pitch Adjustment Bolt Blade Pitch Adjustment ProcedureChanging Blades Stabilizer Ring RemovalTrowel Arm Adjustment Spider RemovalPlace the trowel on a FLAT, Level surface Trowel Arm Removal Remove spider to hydraulic motor retainingscrewRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NTrowel Arm Adjustment Fixture Components Re-AssemblyInstalling Pans Onto Finisher Blades Checking Hydraulic Steering PressureLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Steering Pressure Adjustment Checking Steering PressureCool Oil1 155-175 PSI Hot Oil 145-165 PSI Pitch Pressure Out of Specification Press the left pitch rocker switch downwardPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentSWITCH,KEY Wiring DiagramHydraulic Diagram Troubleshooting Ride-On Hydraulic Trowel TroubleshootingWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help