Multiquip EHTX44Y5 operation manual Stabilizer Ring Removal, Changing Blades

Page 34

mAINTENANCE

If, after making Blade Pitch adjustments the machine is still finishing poorly, blades, trowel arms, and trowel arm bushings may be suspect and should be looked at for adjustment, wear, or damage. See the following sections.

Stabilizer Ring Removal

5.To remove the outer stabilizer ring, (Figure 32), remove the six bolts at the end of each spider arm.

STABILIZER
RING	HEX NUT
	HEX NUT

HEX CAP

SCREW

ROD END

FLAT

WASHER

Figure 32. Stabilizer Ring Removal

6.Examine stabilizer ring for out of round or bends. If ring is damaged, replace ring. If ring is found to be correct with no damage, set aside.

Changing Blades

It is recommended that ALL the blades on the entire machine are changed at the same time. If only one or some of the blades are changed, the machine will not finish concrete consistently and the machine may wobble or bounce.

1.Place the machine on a flat, level surface. Adjust the blade pitch control to make the blades as flat as possible.

2.Note the blade orientation on the trowel arm. This is important for ride-on trowels as the two sets of blades counter-rotate. Lift the machine up, placing blocks under the main guard ring to support it.

3.Remove the bolts and lock washers (Figure 33) that secure the blade to the trowel arm, then remove the blade.

TROWEL

HEX CAP ARM

SCREW

WASHER

Figure 33. Blade Removal

4.Wire brush any build-up of concrete from all six sides of the trowel arm.This is important to properly seat the new blade. Repeat for the remaining arms.

5.Install the new blade, maintaining the proper orientation for direction of rotation.

6.Reinstall the bolts and lock washers.

7.Torque to 9 ft. lbs. (12.2 N.m)

8.Repeat steps 2-7 for all remaining blades.

page 34 — eHtx44y RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13)

Image 34

Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Silicosis Warning Respiratory HazardsEhtx Ride-On Trowel Page Training checklist CompletelyDaily pre-operation checklist Burn hazards SaFeTy meSSageSExplosive fuel hazards Rotating parts hazardsGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy Before servicing equipmentBaTTeRy SaFeTy FueL SaFeTy„ Use well-insulated gloves when picking up the battery „ NeveR lift trowel with the operator on the machine TRaNSpORTINg SaFeTy„ aLWayS shutdown engine before transporting Emission Control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeDIMENSIONS/SPECIFICATIONS EhtxGuaranteed ISO 37442010 Based SpecificationsGuaranteed ISO 112012010 Based Sound Power Level in dBA bGeneral Information Controls and Indicators Hour Meter Indicates number of hours machine has been used25 20 Engine Components Fuel Filter Removes dirt and water from the engine fuelSeat assembly SetupTrowel Setup Instructions Battery SetupEngine Oil Level InspectionHydrauic Oil Level FuelOperation Insert the ignition key into the ignition switch, FigurePlace the engine speed control lever, in the LOW position Steering Place the engine speed control lever, in the High positionTrowel Speed Limiter Control Blade Pitch ControlClean and remove any foreign debris from the trowe Engine Shut-DownMAINTENANCE Remove the air cleaner element Air CleanerOFF position Changing Engine Oil And Filter Checking Engine Oil DailyFilter element from the inside out Vol % Freezing Point Boiling Point Anti Operation in Freezing WeatherGal 9.5 liters 108 226Fuel Filter Radiator MaintenanceFuel/Water Separator Oil And Fuel Lines Battery/Charging SystemCheck and clean battery terminals for corrosion Checking The V-BeltLeft Side Trowel Speed Adjustment Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Engine Tune-UpBlade Pitch Adjustment Procedure Blade Pitch Adjustment BoltStabilizer Ring Removal Changing BladesSpider Removal Trowel Arm AdjustmentPlace the trowel on a FLAT, Level surface Remove spider to hydraulic motor retainingscrew Trowel Arm RemovalRemove the trowel arm from the spider plate Locate the trowel arm adjustment tool P/N Checking Trowel Arm StraightnessRe-Assembly Trowel Arm Adjustment Fixture ComponentsChecking Hydraulic Steering Pressure Installing Pans Onto Finisher BladesLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Checking Steering Pressure Steering Pressure AdjustmentCool Oil1 155-175 PSI Hot Oil 145-165 PSI Press the left pitch rocker switch downward Pitch Pressure Out of SpecificationPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentWiring Diagram SWITCH,KEYHydraulic Diagram Troubleshooting Troubleshooting Ride-On Hydraulic TrowelWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help