Multiquip EHTX44Y5 Engine Components, Fuel Filter Removes dirt and water from the engine fuel

Page 19

ENGINE COMPONENTS

 

 

 

22

11

 

 

 

 

 

 

 

 

 

 

 

 

6

12

16

 

 

 

 

17

 

 

 

 

12

 

 

 

 

 

 

 

23

 

 

 

 

 

 

1

 

 

 

 

 

 

18

 

 

 

 

 

 

15

 

 

 

9

 

 

 

 

 

 

 

 

3

 

 

 

10

 

 

 

 

 

8

 

 

2

4

 

 

 

 

19

 

 

7

 

14

 

 

 

 

 

 

 

 

 

 

21

5

6

20

13

 

 

 

 

Figure 4. Basic Engine Components

Figure 4 shows the basic engine components and their functions. The manufacturer's engine manual provides further instructions and details of operation and servicing.

1.Fuel Filter – Removes dirt and water from the engine fuel.

2.Engine Stop Lever – This lever restricts engine speed (high idle and low idle) through a speed control device linked to the accelerator system.

3.Oil Dip Stick – Remove to check amount and condition of oil in crankcase.

4.Oil Filter – Spin-on type, filters oil for contaminants.

5.Oil Drain Plug – Remove plug to drain crankcase oil.

6.Oil Filler Port – Remove to add fresh crankcase oil.

7.Crankshaft V-Pulley– Check fan V-belt between V-Pulley and alternator to determine proper belt tension.

8.Cooling Fan – Driven by the V-belt, the cooling fan cools the engine by cooling water/antifreeze mixture that circulates through the engine block and cylinder head.

9.V-belt Tension Adjustment – This bolt provides means to adjust the V-belt tension at the alternator bracket.

10.V-belt (Fan belt) – Driven by the engine crank during operation, drives the water pump/fan as well as the alternator.

11.Muffler – Exhaust gases routed here through the muffler.

12.Lifting Eye – Two lifting eyes are provided if the removal/installation of the engine becomes necessary.

13.Alternator – Provides current to the electrical system and charges the battery. Driven by means of a crankshaft/V-belt pulley system.

14.Starter – Starts engine when ignition key is rotated to the "START" position.

15.Flywheel – Main power is taken off from the flywheel end.

16.Air Intake Port – Provides air from the air cleaner to the turbocharger unit.

17.Turbocharger – Provides pressurized intake air to the cylinder by means of a turbine energized by exhaust gas that rotates the blower.

18.Throttle Lever – Controls engine rpm.

19.Fuel Pump – Provides fuel flow to injection pump.

20.Water Pump – Circulates coolant flow through engine.

21.Injection Pump – Provides equal fuel flow to injectors.

22.Air Filter – Helps provide clean source of air flow to turbocharger and engine.

23.Fuel/Water Separator – Separates water, dirt and sludge from fuel helping prevent engine component wear.

ehtx44y5 RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13) — page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Respiratory Hazards Silicosis WarningEhtx Ride-On Trowel Page Completely Training checklistDaily pre-operation checklist Rotating parts hazards SaFeTy meSSageSExplosive fuel hazards Burn hazardsGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160BaTTeRy SaFeTy FueL SaFeTy„ Use well-insulated gloves when picking up the battery „ NeveR lift trowel with the operator on the machine TRaNSpORTINg SaFeTy„ aLWayS shutdown engine before transporting Label must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelEhtx DIMENSIONS/SPECIFICATIONSSound Power Level in dBA b SpecificationsGuaranteed ISO 112012010 Based Guaranteed ISO 37442010 BasedGeneral Information Hour Meter Indicates number of hours machine has been used Controls and Indicators25 20 Fuel Filter Removes dirt and water from the engine fuel Engine ComponentsBattery Setup SetupTrowel Setup Instructions Seat assemblyFuel InspectionHydrauic Oil Level Engine Oil LevelOperation Insert the ignition key into the ignition switch, FigurePlace the engine speed control lever, in the LOW position Place the engine speed control lever, in the High position SteeringBlade Pitch Control Trowel Speed Limiter ControlEngine Shut-Down Clean and remove any foreign debris from the troweMAINTENANCE Remove the air cleaner element Air CleanerOFF position Changing Engine Oil And Filter Checking Engine Oil DailyFilter element from the inside out 108 226 Operation in Freezing WeatherGal 9.5 liters Vol % Freezing Point Boiling Point AntiFuel Filter Radiator MaintenanceFuel/Water Separator Checking The V-Belt Battery/Charging SystemCheck and clean battery terminals for corrosion Oil And Fuel LinesEngine Tune-Up Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Left Side Trowel Speed AdjustmentBlade Pitch Adjustment Bolt Blade Pitch Adjustment ProcedureChanging Blades Stabilizer Ring RemovalSpider Removal Trowel Arm AdjustmentPlace the trowel on a FLAT, Level surface Remove spider to hydraulic motor retainingscrew Trowel Arm RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NTrowel Arm Adjustment Fixture Components Re-AssemblyChecking Hydraulic Steering Pressure Installing Pans Onto Finisher BladesLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Checking Steering Pressure Steering Pressure AdjustmentCool Oil1 155-175 PSI Hot Oil 145-165 PSI Press the left pitch rocker switch downward Pitch Pressure Out of SpecificationPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentSWITCH,KEY Wiring DiagramHydraulic Diagram Troubleshooting Ride-On Hydraulic Trowel TroubleshootingWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help
Top Page Image Contents