Multiquip EHTX44Y5 Specifications, Guaranteed ISO 112012010 Based, Guaranteed ISO 37442010 Based

Page 15

SPECIFICATIONS

Table 2. Noise and Vibration Emissions

Guaranteed ISO 11201:2010 Based

89

Sound Pressure Level at Operator Station in dB(A)a

 

Guaranteed ISO 3744:2010 Based

106

Sound Power Level in dB(A)b

 

Whole Body Vibration Per ISO 2631-1:1997+A1:2010

0.06

in m/s2 ∑A(8)

 

 

 

a. With an uncertainty factor K of 2.5 dB (A) included per Note 1 in section 7.2.1 of EN 12649::2008+A1:2011 b. With an uncertainty factor K of 1.5 dB (A) included per Note 1 in section 7.2.1 of EN 12649::2008+A1:2011

NOTES:

1.Sound Pressure and Power Levels are “A” weighted Measures per ISO 3744:2010. They are measured with the operating condition of the machine which generates the most repeatable but highest values of the sound levels. Under normal circumstances, the sound level will vary depending on the condition of the material being worked upon.

2.The vibration level indicated is the vector sum of the RMS (Root Mean Square) Values of amplitudes on each axis, standardized to an 8 hour exposure period, and obtained using operating condition of the machine that generates the most repeatable but highest values in accordance with the applicable standards for the machine.

3.Per EU Directive 2002/44/EC, the daily exposure action value for whole body vibration is 0.5 m/s2 ∑A(8). The daily exposure limit value is 1.15 m/s2 ∑A(8).

 

Table 3. Engine Specifications

 

 

 

Model

 

Yanmar 3TNV84T-BKSA

Type

 

Vertical inline water cooled diesel engine - direct injected - turbocharged

 

 

 

Cylinders

 

3

 

 

 

Displacement

 

91.29 cu-in. (1.496 L)

 

 

 

Power (Maximum Output)

 

44 HP (32.8 kW/min-1)

 

 

 

Bore and Stroke

 

3.31 in. x 3.54 in. (84 mm x 90 mm)

 

 

 

Cooling System

 

Water-Cooled Radiator, Water-antifreeze ratio 50/50

 

 

 

Engine Oil Capacity

 

7.08 US qt. (6.7 liter) dipstick upper limit

 

 

 

P.T.O Position

 

Flywheel side

Fuel Tank

 

Approx. 11 U.S. gallons (41.64 liters)

 

 

 

Fuel

 

Diesel - No. 2-D (ASTM D975)

 

 

 

Starting System

 

12V Electric Starter with Glow Plug

 

 

 

Dry Weight

 

341.7 lbs (155 Kg.)

 

 

 

Dimensions (L x W x H)

 

22.2 in. x 19.1 in. x 24.5 in

 

(564 mm x 486 mm x 622 mm).

 

 

 

 

 

ehtx44y5 RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Respiratory Hazards Silicosis WarningEhtx Ride-On Trowel Page Completely Training checklistDaily pre-operation checklist Rotating parts hazards SaFeTy meSSageSExplosive fuel hazards Burn hazardsGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160FueL SaFeTy BaTTeRy SaFeTy„ Use well-insulated gloves when picking up the battery TRaNSpORTINg SaFeTy „ NeveR lift trowel with the operator on the machine„ aLWayS shutdown engine before transporting Label must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelEhtx DIMENSIONS/SPECIFICATIONSSound Power Level in dBA b SpecificationsGuaranteed ISO 112012010 Based Guaranteed ISO 37442010 BasedGeneral Information Hour Meter Indicates number of hours machine has been used Controls and Indicators25 20 Fuel Filter Removes dirt and water from the engine fuel Engine ComponentsBattery Setup SetupTrowel Setup Instructions Seat assemblyFuel InspectionHydrauic Oil Level Engine Oil LevelInsert the ignition key into the ignition switch, Figure OperationPlace the engine speed control lever, in the LOW position Place the engine speed control lever, in the High position SteeringBlade Pitch Control Trowel Speed Limiter ControlEngine Shut-Down Clean and remove any foreign debris from the troweMAINTENANCE Air Cleaner Remove the air cleaner elementOFF position Checking Engine Oil Daily Changing Engine Oil And FilterFilter element from the inside out 108 226 Operation in Freezing WeatherGal 9.5 liters Vol % Freezing Point Boiling Point AntiRadiator Maintenance Fuel FilterFuel/Water Separator Checking The V-Belt Battery/Charging SystemCheck and clean battery terminals for corrosion Oil And Fuel LinesEngine Tune-Up Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Left Side Trowel Speed AdjustmentBlade Pitch Adjustment Bolt Blade Pitch Adjustment ProcedureChanging Blades Stabilizer Ring RemovalTrowel Arm Adjustment Spider RemovalPlace the trowel on a FLAT, Level surface Trowel Arm Removal Remove spider to hydraulic motor retainingscrewRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NTrowel Arm Adjustment Fixture Components Re-AssemblyInstalling Pans Onto Finisher Blades Checking Hydraulic Steering PressureLifting/Crush Hazard. do not lift trowel with pans attached Hydraulic Pump Pressure Test Ports Steering Pressure Adjustment Checking Steering PressureCool Oil1 155-175 PSI Hot Oil 145-165 PSI Pitch Pressure Out of Specification Press the left pitch rocker switch downwardPitch Pressure Check Pitch Pressure Adjustment Pitch Pressure AdjustmentSWITCH,KEY Wiring DiagramHydraulic Diagram Troubleshooting Ride-On Hydraulic Trowel TroubleshootingWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help
Top Page Image Contents