Multiquip EHTX44Y5 Steering, Place the engine speed control lever, in the High position

Page 23

OPERATION

6.Turn ignition key fully clockwise and listen for engine to start. Once engine has started release ignition key. Let the engine warm for a few minutes.

7.Place the engine speed control lever, (Figure 12) in the HIGH position.

ENGINE SPEED

CONTROL LEVER

Figure 12. Engine Speed Control Lever (High)

8.The engine should be running at full RPM's

9.Let the engine idle for 3-5 minutes.

10.Repeat this section a few times to get fully acquainted with the engine starting procedure.

Steering

Two joysticks (Figure 14) located to the left and right of the operator’s seat provide directional control for the trowel. Table 4 illustrates the various directional positions of the joysticks and their effect on the ride-on trowel.

NOTICE

All directional references with respect to the steering Control Joysticks are from the operator’s seat position.

1.The foot pedal, (Figure 13) solely controls blade speed. The position of the foot pedal determines the blade speed. Slow blade speed is obtained by slightly depressing the pedal. Maximum blade speed is obtained by fully depressing the pedal.

Figure 13. Blade Speed Control Foot Pedal

2.Push both the left and right Control Joysticks forward. See Figure 14

FORWARD

LEFT JOYSTICK

 

CONTROL

LEFT

 

REVERSE

FORWARD

 

 

RIGHT

REVERSE

 

RIGHT JOYSTICK

 

CONTROL

Figure 14. Left and Right Control Joysticks

Table 4. Control Joystick Directional Positioning

CONTROL JOYSTICK

RESULT

& DIRECTION

 

Move LEFT Joystick

Causes only the

left side of the

FORWARD

ride-on trowel to

 

 

move forward.

Move LEFT Joystick

Causes only the

left side of the

BACKWARD

ride-on trowel to

 

 

move backward.

Move RIGHT Joystick

Causes only the

FORWARD

right side of the

 

ride-on trowel to

 

move forward.

Move RIGHT Joystick

Causes only the

BACWARD

right side of the

 

ride-on trowel to

 

move backward.

Move BOTH Joysticks

Causes the ride-on trowel

FORWARD

to move forward in

 

a straight line.

Move BOTH Joysticks

Causes the ride-on trowel

BACKWARD

to move backard in

 

a straight line.

Move BOTH Joysticks

Causes the ride-on trowel

to the RIGHT

to move to the right.

Move BOTH Joysticks

Causes the ride-on trowel

to the LEFT

to move to the left.

ehtx44y5 RIDE-ON TROWEL • operation manual — rev. #0 (01/16/13) — page 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model eHTX44Y5 Fuel and chemical exposure Warnings Respiratory Hazards Silicosis WarningEhtx Ride-On Trowel Page Completely Training checklistDaily pre-operation checklist Rotating parts hazards SaFeTy meSSageSExplosive fuel hazards Burn hazardsGeNeRaL SaFeTy Before servicing equipment TROWeL SaFeTyENgINe SaFeTy Order Form PT-160„ Use well-insulated gloves when picking up the battery FueL SaFeTyBaTTeRy SaFeTy „ aLWayS shutdown engine before transporting TRaNSpORTINg SaFeTy„ NeveR lift trowel with the operator on the machine Label must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission Control LabelEhtx DIMENSIONS/SPECIFICATIONSSound Power Level in dBA b SpecificationsGuaranteed ISO 112012010 Based Guaranteed ISO 37442010 BasedGeneral Information Hour Meter Indicates number of hours machine has been used Controls and Indicators25 20 Fuel Filter Removes dirt and water from the engine fuel Engine ComponentsBattery Setup SetupTrowel Setup Instructions Seat assemblyFuel InspectionHydrauic Oil Level Engine Oil LevelPlace the engine speed control lever, in the LOW position Insert the ignition key into the ignition switch, FigureOperation Place the engine speed control lever, in the High position SteeringBlade Pitch Control Trowel Speed Limiter ControlEngine Shut-Down Clean and remove any foreign debris from the troweMAINTENANCE OFF position Air CleanerRemove the air cleaner element Filter element from the inside out Checking Engine Oil DailyChanging Engine Oil And Filter 108 226 Operation in Freezing WeatherGal 9.5 liters Vol % Freezing Point Boiling Point AntiFuel/Water Separator Radiator MaintenanceFuel Filter Checking The V-Belt Battery/Charging SystemCheck and clean battery terminals for corrosion Oil And Fuel LinesEngine Tune-Up Right Side Trowel Speed AdjustmentChecking/Adjusting Trowel Speed Left Side Trowel Speed AdjustmentBlade Pitch Adjustment Bolt Blade Pitch Adjustment ProcedureChanging Blades Stabilizer Ring RemovalPlace the trowel on a FLAT, Level surface Trowel Arm AdjustmentSpider Removal Remove the trowel arm from the spider plate Trowel Arm RemovalRemove spider to hydraulic motor retainingscrew Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NTrowel Arm Adjustment Fixture Components Re-AssemblyLifting/Crush Hazard. do not lift trowel with pans attached Installing Pans Onto Finisher BladesChecking Hydraulic Steering Pressure Hydraulic Pump Pressure Test Ports Cool Oil1 155-175 PSI Hot Oil 145-165 PSI Steering Pressure AdjustmentChecking Steering Pressure Pitch Pressure Check Pitch Pressure Out of SpecificationPress the left pitch rocker switch downward Pitch Pressure Adjustment Pitch Pressure AdjustmentSWITCH,KEY Wiring DiagramHydraulic Diagram Troubleshooting Ride-On Hydraulic Trowel TroubleshootingWiring? Troubleshooting engine Dipstick HERE’S HOW to GET Help
Top Page Image Contents