Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp MDG-120PVV, MD-170PTVW MDG-120 Specifications, Maytag Co, 113395

Models: MD-170PTVW

1 52

Download 52 pages 9.4 Kb

Page 9

MDG-120 Specifications

MDG-120 Specifications

NOTE: The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.

113395 - 6

Maytag Co.

7

Image 9

American Dryer Corp MDG-120PVV, MD-170PTVW installation manual MDG-120 Specifications, Maytag Co, 113395

Contents

Phase 7 / Non-Coin / Dual Timer with S.A.F.E. System RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCEMDG-120PVV / MD-170PTVW Installation Manual Retain This Manual In A Safe Place For Future Reference Maytag Co“IMPORTANT NOTE TO PURCHASER” FOR YOUR SAFETY The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONALINJURY OR FIRE COULD RESULT SECTION Table of ContentsSECTION SECTIONSECTION SAFETY PRECAUTIONSWARNING PERSONAL INJURY OR FIRE COULD RESULT SHOULD THE DRYER DOOR SWITCH, LINT DRAWER SWITCH, OR THE HEAT SAFETY CIRCUITS EVER BE DISABLED A. MDG-120 SPECIFICATIONS SPECIFICATIONSSECTION 54.4 kgMDG-120 Specifications Maytag Co113395 Electric B. MD-170 SPECIFICATIONSMD-170 Specifications Maytag Co113395 INSTALLATION PROCEDURES A. LOCATION REQUIREMENTSSECTION B. UNPACKING/SETTING UP e. Lift the console module off the dryer base 3. Exhaust Transition Piece THIS EXHAUST DUCT TRANSITION PIECE MUST BE INSTALLED FIRSTNOTE Allowances must be made for opening the control door C. DRYER ENCLOSURE REQUIREMENTSD. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS 1. Single Dryer Venting 4. Multiple Dryer Common Venting 1. Electrical Requirements F. ELECTRICAL INFORMATIONMD-120 Gas MD-170 Gas and SteamIMPORTANT Figures shown are for reversing models 3. Grounding G. GAS INFORMATION TYPE OF GAS TYPE OF GAS8.7 mb 26.1 mbWARNING NEVER TEST FOR GAS LEAKS WITH A FLAME IMPORTANT The dryer and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig 3.5 kPa H. PREPARATION FOR OPERATION I. PREOPERATIONAL TEST BASKET TUMBLER COATING K. OPERATING INSTRUCTIONS J. SHUTDOWN INSTRUCTIONSa. GAS MODELS - discontinue the gas supply 1 SHUT OFF external gas supply shutoff valveAir Pressure CompressedAir Supply L. COMPRESSED AIR REQUIREMENTS MD-170 OnlyM. STEAM INFORMATION MD-170 Only Operating Steam PressureSTEAM DAMPER SYSTEM Air Pressure CompressedAir Supply Normal6. Steam Damper Air Piston Flow Control Operation Adjustment A. SERVICE SERVICE/PARTS INFORMATIONB. PARTS SECTIONA. RETURNING WARRANTY CARDS WARRANTY INFORMATIONB. WARRANTY SECTIONA. CLEANING ROUTINE MAINTENANCESUGGESTED CLEANING SCHEDULE SECTIONSTEAM DRYERS 90 DAYS6 MONTHS B. ADJUSTMENTS C. LUBRICATION7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER A. PHASE MANUAL RESET BURNER HI-LIMIT INSTRUCTIONSB. DUAL TIMER SECTIONVIIDATA LABEL INFORMATION SECTIONVIIIAdjustment Position Number REVERSING TIMER SPIN/DWELLADJUSTMENTSTIMING LEGEND SPIN TIMESECTION PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS2. For Models with Direct Spark Ignition DSI Module Type MICROPROCESSOR MODELS ONLY INSTALLATIONSECTION SENSORACTIVATED FIRE EXTINGUISHING S.A.F.E. SYSTEMOPTIONAL MANUAL BYPASS Typical Water SupplyFIRE SUPPRESSION SYSTEM THEORY OF OPERATION SYSTEM RESET FIRE SUPPRESSION SYSTEM DIAGNOSTICSFIRE SUPPRESSION SYSTEM WATER VALVE CHECK FIRE SUPPRESSION SYSTEM DIAGNOSTICS MESSAGES 6 - 05/01/07