Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp MD-170PTVW, MDG-120PVV installation manual MD-120 Gas, MD-170 Gas and Steam

Models: MD-170PTVW

1 52

Download 52 pages 9.4 Kb

Page 22

IMPORTANT: Figures shown are for reversing models.

2.Electrical Service Specifications

IMPORTANT: Figures shown are for reversing models.

MD-120 Gas

ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)

IMPORTANT: 208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify exact voltage.

NOTES: A. When fuses are used they must be dual element, time delay, current limiting, class RK1 or RK5 ONLY. Calculate/determine correct fuse value, by applying either local and/or National Electrical Codes to listed appliance amp draw data.

B.Circuit breakers are thermal-magnetic (industrial) motor curve type ONLY. For others, calculate/verify correct breaker size according to appliance amp draw rating and type of breaker used.

C.Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

	SERVICE	PHASE	WIRE	APPROX.		CIRCUIT
	SERVICE		WIRE	AMP DRAW		CIRCUIT
	VOLTAGE		SERVICE	AMP DRAW		BREAKER
	VOLTAGE		SERVICE	60 Hz	50 Hz	BREAKER
				60 Hz	50 Hz
	208	3ø	3	14.5	—	20
	240	3ø	3	14.6	—	20
	230	3ø	3	—	17.4	25
	380	3ø	3	8.5	—	15
	380 / 400	3ø	4*	—	8.7	15
	416	3ø	4*	—	9.0	15
	440	3ø	3	8.7	—	15
	460 / 480	3ø	3	7.8	—	15
	575	3ø	3	5.8	—	15
	* 3-Wire is available.					4/20/07

MD-170 Gas and Steam

ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)

IMPORTANT: 208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify exact voltage.

NOTES: A. When fuses are used they must be dual element, time delay, current limiting, class RK1 or RK5 ONLY. Calculate/determine correct fuse value, by applying either local and/or National Electrical Codes to listed appliance amp draw data.

B.Circuit breakers are thermal-magnetic (industrial) motor curve type ONLY. For others, calculate/verify correct breaker size according to appliance amp draw rating and type of breaker used.

C.Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

	SERVICE	PHASE	WIRE	APPROX.		CIRCUIT
	SERVICE		WIRE	AMP DRAW		CIRCUIT
	VOLTAGE		SERVICE	AMP DRAW		BREAKER
	VOLTAGE		SERVICE	60 Hz	50 Hz	BREAKER
				60 Hz	50 Hz
	208	3ø	3	28.3	—	50
	240	3ø	3	26.7	—	45
	230	3ø	3	—	31.9	50
	380	3ø	3	16.2	—	25
	380 / 400	3ø	4*	—	16.1	25
	416	3ø	4*	—	16.0	25
	440	3ø	3	14.4	—	20
	460 / 480	3ø	3	13.9	—	20
	575	3ø	3	11.4	—	20
	* 3-Wire is available.					4/20/07

20

Maytag Co.

113395 - 6

Image 22

American Dryer Corp MD-170PTVW MD-120 Gas, MD-170 Gas and Steam, IMPORTANT Figures shown are for reversing models

Contents

RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE Phase 7 / Non-Coin / Dual Timer with S.A.F.E. SystemMDG-120PVV / MD-170PTVW Installation Manual Maytag Co Retain This Manual In A Safe Place For Future Reference“IMPORTANT NOTE TO PURCHASER” FOR YOUR SAFETY The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONALINJURY OR FIRE COULD RESULT SECTION Table of ContentsSECTION SECTIONSAFETY PRECAUTIONS SECTIONWARNING PERSONAL INJURY OR FIRE COULD RESULT SHOULD THE DRYER DOOR SWITCH, LINT DRAWER SWITCH, OR THE HEAT SAFETY CIRCUITS EVER BE DISABLED SECTION SPECIFICATIONSA. MDG-120 SPECIFICATIONS 54.4 kgMaytag Co MDG-120 Specifications113395 B. MD-170 SPECIFICATIONS ElectricMaytag Co MD-170 Specifications113395 A. LOCATION REQUIREMENTS INSTALLATION PROCEDURESSECTION B. UNPACKING/SETTING UP e. Lift the console module off the dryer base THIS EXHAUST DUCT TRANSITION PIECE MUST BE INSTALLED FIRST 3. Exhaust Transition PieceC. DRYER ENCLOSURE REQUIREMENTS NOTE Allowances must be made for opening the control doorD. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS 1. Single Dryer Venting 4. Multiple Dryer Common Venting F. ELECTRICAL INFORMATION 1. Electrical RequirementsMD-170 Gas and Steam MD-120 GasIMPORTANT Figures shown are for reversing models 3. Grounding G. GAS INFORMATION 8.7 mb TYPE OF GASTYPE OF GAS 26.1 mbWARNING NEVER TEST FOR GAS LEAKS WITH A FLAME IMPORTANT The dryer and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig 3.5 kPa H. PREPARATION FOR OPERATION I. PREOPERATIONAL TEST BASKET TUMBLER COATING a. GAS MODELS - discontinue the gas supply J. SHUTDOWN INSTRUCTIONSK. OPERATING INSTRUCTIONS 1 SHUT OFF external gas supply shutoff valveAir Supply CompressedAir Pressure L. COMPRESSED AIR REQUIREMENTS MD-170 OnlyOperating Steam Pressure M. STEAM INFORMATION MD-170 OnlySTEAM DAMPER SYSTEM Air Supply CompressedAir Pressure Normal6. Steam Damper Air Piston Flow Control Operation Adjustment B. PARTS SERVICE/PARTS INFORMATIONA. SERVICE SECTIONB. WARRANTY WARRANTY INFORMATIONA. RETURNING WARRANTY CARDS SECTIONSUGGESTED CLEANING SCHEDULE ROUTINE MAINTENANCEA. CLEANING SECTION90 DAYS STEAM DRYERS6 MONTHS C. LUBRICATION B. ADJUSTMENTS7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER B. DUAL TIMER MANUAL RESET BURNER HI-LIMIT INSTRUCTIONSA. PHASE SECTIONVIISECTIONVIII DATA LABEL INFORMATIONTIMING LEGEND REVERSING TIMER SPIN/DWELLADJUSTMENTSAdjustment Position Number SPIN TIMEPROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS SECTION2. For Models with Direct Spark Ignition DSI Module Type SECTION INSTALLATIONMICROPROCESSOR MODELS ONLY SENSORACTIVATED FIRE EXTINGUISHING S.A.F.E. SYSTEMTypical Water Supply OPTIONAL MANUAL BYPASSFIRE SUPPRESSION SYSTEM THEORY OF OPERATION FIRE SUPPRESSION SYSTEM DIAGNOSTICS SYSTEM RESETFIRE SUPPRESSION SYSTEM WATER VALVE CHECK FIRE SUPPRESSION SYSTEM DIAGNOSTICS MESSAGES 6 - 05/01/07