Manuals / American Dryer Corp / Laundry Appliance / Clothes Dryer

American Dryer Corp MDG-120PVV This Exhaust Duct Transition Piece Must Be Installed First

Models: MD-170PTVW

1 52

Download 52 pages 9.4 Kb

Page 15

3.Exhaust Transition Piece

3.Exhaust Transition Piece

WARNING

An exhaust duct transition piece is shipped inside of the dryer’s tumbler and must be installed on the dryer’s exhaust duct, with the hardware provided, BEFORE location venting is connected to the dryer.

THIS EXHAUST DUCT TRANSITION PIECE

MUST BE INSTALLED FIRST!

Failure to observe this installation requirement may result in damage to the dryer, create a FIRE HAZARD and will VOID the manufacturer’s warranty.

012999JEV-GS/cj

P/N: 114092

Inside the basket (tumbler) of this dryer is an exhaust transition piece that must be installed on the outlet of the exhaust before any further venting is connected:

a.Remove the exhaust transition piece from the basket (tumbler) and place it on the exhaust outlet.

b.Using the screws provided, secure the exhaust transition piece to the dryer.

NOTE: It is recommended that this joint be taped as well as ALL other duct joints to prevent moisture and lint from escaping into the building.

113395 - 6

Maytag Co.

13

Image 15

American Dryer Corp MDG-120PVV This Exhaust Duct Transition Piece Must Be Installed First, Exhaust Transition Piece

Contents

Phase 7 / Non-Coin / Dual Timer with S.A.F.E. System RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCEMDG-120PVV / MD-170PTVW Installation Manual Retain This Manual In A Safe Place For Future Reference Maytag Co“IMPORTANT NOTE TO PURCHASER” FOR YOUR SAFETY The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONALINJURY OR FIRE COULD RESULT SECTION Table of ContentsSECTION SECTIONSECTION SAFETY PRECAUTIONSWARNING PERSONAL INJURY OR FIRE COULD RESULT SHOULD THE DRYER DOOR SWITCH, LINT DRAWER SWITCH, OR THE HEAT SAFETY CIRCUITS EVER BE DISABLED 54.4 kg SPECIFICATIONSA. MDG-120 SPECIFICATIONS SECTIONMDG-120 Specifications Maytag Co113395 Electric B. MD-170 SPECIFICATIONSMD-170 Specifications Maytag Co113395 INSTALLATION PROCEDURES A. LOCATION REQUIREMENTSSECTION B. UNPACKING/SETTING UP e. Lift the console module off the dryer base 3. Exhaust Transition Piece THIS EXHAUST DUCT TRANSITION PIECE MUST BE INSTALLED FIRSTNOTE Allowances must be made for opening the control door C. DRYER ENCLOSURE REQUIREMENTSD. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS 1. Single Dryer Venting 4. Multiple Dryer Common Venting 1. Electrical Requirements F. ELECTRICAL INFORMATIONMD-120 Gas MD-170 Gas and SteamIMPORTANT Figures shown are for reversing models 3. Grounding G. GAS INFORMATION 26.1 mb TYPE OF GASTYPE OF GAS 8.7 mbWARNING NEVER TEST FOR GAS LEAKS WITH A FLAME IMPORTANT The dryer and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig 3.5 kPa H. PREPARATION FOR OPERATION I. PREOPERATIONAL TEST BASKET TUMBLER COATING 1 SHUT OFF external gas supply shutoff valve J. SHUTDOWN INSTRUCTIONSK. OPERATING INSTRUCTIONS a. GAS MODELS - discontinue the gas supplyL. COMPRESSED AIR REQUIREMENTS MD-170 Only CompressedAir Pressure Air SupplyM. STEAM INFORMATION MD-170 Only Operating Steam PressureSTEAM DAMPER SYSTEM Normal CompressedAir Pressure Air Supply6. Steam Damper Air Piston Flow Control Operation Adjustment SECTION SERVICE/PARTS INFORMATIONA. SERVICE B. PARTSSECTION WARRANTY INFORMATIONA. RETURNING WARRANTY CARDS B. WARRANTYSECTION ROUTINE MAINTENANCEA. CLEANING SUGGESTED CLEANING SCHEDULESTEAM DRYERS 90 DAYS6 MONTHS B. ADJUSTMENTS C. LUBRICATION7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER SECTIONVII MANUAL RESET BURNER HI-LIMIT INSTRUCTIONSA. PHASE B. DUAL TIMERDATA LABEL INFORMATION SECTIONVIIISPIN TIME REVERSING TIMER SPIN/DWELLADJUSTMENTSAdjustment Position Number TIMING LEGENDSECTION PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS2. For Models with Direct Spark Ignition DSI Module Type SENSORACTIVATED FIRE EXTINGUISHING S.A.F.E. SYSTEM INSTALLATIONMICROPROCESSOR MODELS ONLY SECTIONOPTIONAL MANUAL BYPASS Typical Water SupplyFIRE SUPPRESSION SYSTEM THEORY OF OPERATION SYSTEM RESET FIRE SUPPRESSION SYSTEM DIAGNOSTICSFIRE SUPPRESSION SYSTEM WATER VALVE CHECK FIRE SUPPRESSION SYSTEM DIAGNOSTICS MESSAGES 6 - 05/01/07