RIDGID JP0610 manual Install the Leveling Feet, Mounting the Motor, Carriage Head Bolt 16-18 x 1/2

Page 14

Assembly (continued)

Install the Leveling Feet

1.Turn the base upside down.

2.From the hardware pack find the following:

4 Rubber Leveling Feet

8 Flat Washer 3/8

8 Hex Nut 3/8

3.Thread one 3/8 nut onto each of the leveling feet until the nut is 1/2" from the foot. Do this for all four feet.

4.Attach the leveling feet as shown. Place one 3/8 washer on the bottom side of the foot mount tab and one washer on top. Bolt the feet in place with the sec- ond 3/8 nut. Tighten the nuts down with a wrench.

NOTE: Once the jointer is in its permanent location the leveling feet may need to be adjusted.

 

3/8 Flat Washer

Leveling Foot

Leveling Foot

 

3/8-16 Hex Nut Cabinet ˜

Mounting the Motor

1.Turn the cabinet upside down and place a 4 x 4 block under the right side of the cabinet so the base is tilted as shown. This will elevate the motor mount so it is level with the floor making assembly easier.

2.From the hardware pack find the following:

4Carriage Head Bolts 5/16-18 x 1/2"

4Serrated Flange Hex Nuts 5/16

2Machine Screws with Washer Head 3/16" From among the loose parts find the following:

1Motor and Switch Assembly

3.Place the motor on the motor mount as shown. Make sure the motor shaft faces the rear of the cabinet (away from the side with RIDGID label).

4.Bolt the motor to the motor mount using the four 5/16 car- riage head bolts and four 5/16 serrated flange nuts. The bolts should be placed through the motor mount into the motor bracket as shown. Do not tighten the bolts at this time.

5.Using the two 3/16 screws, mount the switch into place as shown. Make sure the switch is right side up.

Carriage Head Bolt

5/16-18 x 1/2"

Machine Screw w/Washer Head 3/16-24 x 3/8

Serrated Flange

Hex Nut 5/16

Motor Assembly

with Switch

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents
235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex BoltAssembly Cabinet and Motor Mount AssemblyMounting the Motor Install the Leveling FeetSerrated Flange Hex Nut 5/16 Motor Assembly With Switch Carriage Head Bolt 16-18 x 1/2Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Serr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobPage On-Off Switch Angle GaugeCutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Angle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Repair Parts 2120 45 46Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call