RIDGID JP0610 manual Repair Parts

Page 39

Repair Parts

Parts List for RIDGID 6-1/8" Jointer/Planer

Model No. JP06101

RIDGID parts are available on-line at www.ridgidparts.com

Figure 2

Always order by Part Number - Not by Key Number

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	1	828689	Holder Fence
	2	805563-6	* Washer .515 x 1-1/8 x 3/32
	3	828400	Knob Fence
	4	828517	Sleeve Fence
	5
	6	828518	Nut Tee Fence
	7	828524	Plate Stop
	8	828522	Bolt Shoulder 9mm x 19mm
	9	805467-11	* Screw Hex Hd 5/16-18 x 1-3/4
	10	829507	Plate Fence Pivot
	11	828516	Screw Pivot
	12	118645	Nut Hex Jam 3/8-16
	13	828712	Knob Fence Tilt
	14	805467-6	* Screw Hex Hd 5/16-18 x 1
	15	805482	* Nut Hex Jam 5/16-18
	16	828447	Stud Pivot

* Standard hardware item, may be purchased locally

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	17	813640	* Nut Hex Jam 1/2-20
	18	829506	Fence
	19	805297-8	* Screw Flat Hd Soc 5/16-18 x 1-1/2
	20	828520	Nut Handle
	21	828525	Bolt Shoulder 10 x 6
	22	828521	Nut Pivot
	23	828519	Stop Fence
	24	805485	* Nut Hex Jam 7/16-14
	25	829508	Shaft Lock
	26	828526	Collar Lock

27805551-2 * Washer Flat 1/4 x 1/2 x 1/16

28809491-5 * Screw Pan Cr 1/4-20 x 1/2

29	828401	Handle Asm
30	828529	Bracket Fence

31805567-6 Washer .63 I.D. x 1-3/4 x 5/32

32805467 * Screw Hex Hd 5/16-18 x 1-1/4

39

Image 39

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsDon’t Force Tool Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Keep Children AwayMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Prong Plug Properly Grounded Outlet Grounding General Electrical ConnectionsVolt, 60 Hz. Tool Information Changing Motor VoltageMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Serrated Hex Bolt Loose Parts From Hardware PackCabinet and Motor Mount Assembly AssemblyCarriage Head Bolt 16-18 x 1/2 Install the Leveling FeetSerrated Flange Hex Nut 5/16 Motor Assembly With Switch Mounting the MotorTensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetAlign Belt Tighten Motor Mount Nuts 20 x 5/8 Installing the Pulley GuardInstalling Handwheel Serr 3/16-24 x 3/8 Belt GuardOutfeed Socket Head Screw Extension even with Outfeed table Adjusting Table ExtensionAttach Sawdust Chute Tool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8Fence Lock Knob Nut Washer 1/2 Actual Size Not Install Cutter Head GuardAssembly Fence Nut Mount Assemble Fence To BedPan Head Screw Knob Adjusting Guard SpringAdjusting the Leveling Feet Cutter Head Guard Functional CheckPage Angle Gauge On-Off SwitchAlignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningOutfeed Table Adjustment Stop Screw Bar Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Angle Gauge UseSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Plan your work Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Push blocks and push sticksBefore Leaving the jointer/planer Inspect your workpieceFeeding the Workpiece Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Stop Pin OperationJointing Without Push Blocks PlaningJointing Beveling/ChamferingFace Rabbet End Edge Using the Hold-Down/Push-BlocksRabbeting Support Long WorkpiecesSliding Lock Knob Sliding Fence OperationLubrication Maintenance and LubricationWiring Diagram MaintenanceTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor 2120 45 46 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts Call DAY Satisfaction Guarantee Policy