Table of Contents
Section | Page | Section | Page |
Table of Contents | 2 | Cutter Head Guard Functional Check | 19 |
Safety Instructions For Jointer/Planer | 2 | Adjusting Guard Spring | 19 |
Safety Symbols | 2 | Adjusting the Leveling Feet | 19 |
Major Hazards | 3 | Getting to Know Your Jointer/Planer | 20 |
Before Using the Jointer/Planer | 3 | Alignments | 22 |
Safety Labels and Indicators on the Jointer/Planer ...4 | Cutter Knife Alignment/Adjustments | 22 | |
When Installing Or Moving the Jointer/Planer | 4 | Cutter Knife Sharpening | 23 |
Before Each Use | 4 | Outfeed Table Adjustment | 24 |
To Reduce the Risk of Injury From Jams, Slips Or |
| Adjusting Table Gibs | 25 |
Thrown Pieces (Kickbacks Or Throwbacks) | 5 | Angle Gauge Use | 25 |
Plan Ahead To Protect Your Eyes, Hands, |
| Fence Tilt Use and Bevel Stop Adjustment | 25 |
Face and Ears | 5 | Safety Instructions for Basic Jointer/Planer |
|
Inspect Your Workpiece | 5 | Operation | 26 |
Whenever Jointer/Planer Is Running | 6 | Before Each Use | 26 |
Before Leaving the Jointer/Planer | 6 | Feeding the Workpiece (All Operations) | 27 |
Glossary of Terms for Woodworking | 6 | To Reduce the Risk of Injury From Jams, Slips Or |
|
Motor Specifications and Electrical Requirements | 7 | Thrown Pieces (Kickbacks Or Throwbacks) | 27 |
Power Supply and Motor Specifications | 7 | Plan Ahead to Protect Your Eyes, Hands, |
|
General Electrical Connections | 8 | Face and Ears | 28 |
8 | Whenever Jointer/Planer Is Running | 28 | |
Changing Motor Voltage | 8 | Basic Jointer/Planer Cutting Operations | 29 |
Motor Safety Protection | 9 | Depth of Cut Handwheel Operation | 29 |
Wire Sizes | 9 | Stop Pin Operation | 29 |
Unpacking and Checking Contents | 10 | Feeding the Workpiece | 29 |
Tools Needed | 10 | Planing | 30 |
Unpacking | 10 | Jointing | 30 |
List of Loose Parts | 10 | Beveling/Chamfering | 30 |
Loose Parts | 11 | Rabbeting | 31 |
Loose Parts (From Hardware Pack) | 12 | Stop Pin Operation | 31 |
Assembly | 13 | Support Long Workpieces | 31 |
Cabinet and Motor Mount Assembly | 13 | Using the | 31 |
Install the Leveling Feet | 14 | Sliding Fence Operation | 32 |
Mounting the Motor | 14 | Maintenance and Lubrication | 33 |
Mounting Jointer Table to Cabinet | 15 | Maintenance | 33 |
Tensioning Belt and Installing Rear Panel |
| Lubrication | 33 |
and Pulley Guard | 15 | Wiring Diagram | 33 |
Installing Handwheel | 16 | Troubleshooting Guide | 34 |
Attach Sawdust Chute | 17 | General | 34 |
Adjusting Table Extension | 17 | Motor | 35 |
Assemble Fence To Bed | 18 | Repair Parts | 36 |
Install Cutter Head Guard | 18 |
|
|
Safety Instructions For Jointer/Planer
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
Safety Symbols
DANGER: indicates an imminently hazardous situa- tion which, if not avoided, will result in death or serious injury.
WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe prac- tices that may cause property damage.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
2