RIDGID JP0610 manual Repair Parts, 2120 45 46

Page 36

Repair Parts

Parts List for RIDGID 6-1/8" Jointer/Planer

Model No. JP06101

RIDGID parts are available on-line at www.ridgidparts.com

			Figure 1
	36		35
	36
37		44	1
37			1

38

35

34

10

33

32

13

12

31

2

			11
	20	14	9
		30	9

11

12	13
12	9	3
		3

4

8

5

14

6

29

28

27

26

24

25

41

39

40

		15	16	7


23			15	17

18

19

2120 22

42

45 46 47

43

36

Image 36

Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceWhenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force ToolMotor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingMotor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex BoltAssembly Cabinet and Motor Mount AssemblyInstall the Leveling Feet Serrated Flange Hex Nut 5/16 Motor Assembly With SwitchMounting the Motor Carriage Head Bolt 16-18 x 1/2Tensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetAlign Belt Tighten Motor Mount Nuts Installing the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Outfeed Socket Head Screw Extension even with Outfeed tableInstall Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobPage On-Off Switch Angle GaugeCutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Adjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw BarSafety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your workInspect your workpiece Before Leaving the jointer/planerBasic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the WorkpiecePlaning JointingBeveling/Chamfering Jointing Without Push BlocksUsing the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance and Lubrication Wiring DiagramMaintenance LubricationTroubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts 2120 45 46Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call