RIDGID JP0610 Installing the Pulley Guard, Installing Handwheel, Serr 3/16-24 x 3/8 Belt Guard

Page 16

Assembly (continued)

Installing the Pulley Guard

1.From the hardware pack locate the following: From among the loose parts find the following:

4 Pan Head Cross Serrated Screws 3/16-24 x 3/8" Belt Guard

2.With assistance set the jointer upright.

3.Mount the belt guard in place as shown using the four 3/16" screws.

Screw Pan Head Cr

 

Serr 3/16-24 x 3/8"

Belt Guard

 

NOTE: Fence mount removed for clarity

Installing Handwheel

1.

From the hardware pack find the following:

 

 

 

1

Screw Pan Head 1/4-20 x 5/8

 

 

 

1

Washer 1/4

 

 

 

Screw Pan Head w/Washer

2.

From among the loose parts find the following:

1/4-20 x 5/8"

 

 

Handwheel

1 Handwheel

3.Slip the handwheel onto the infeed table elevation shaft and install the washer and screw as shown.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceWhenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force ToolPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingWire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex BoltAssembly Cabinet and Motor Mount AssemblyInstall the Leveling Feet Serrated Flange Hex Nut 5/16 Motor Assembly With SwitchMounting the Motor Carriage Head Bolt 16-18 x 1/2Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelAlign Belt Tighten Motor Mount Nuts Installing the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Outfeed Socket Head Screw Extension even with Outfeed tableInstall Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobPage On-Off Switch Angle GaugeCutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Adjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw BarBefore Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your workInspect your workpiece Before Leaving the jointer/planerBasic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the WorkpiecePlaning JointingBeveling/Chamfering Jointing Without Push BlocksUsing the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance and Lubrication Wiring DiagramMaintenance LubricationGeneral Troubleshooting GuideTrouble Probable Cause Remedy Motor Repair Parts 2120 45 46Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call
Top Page Image Contents