RIDGID JP0610 manual Attach Sawdust Chute, Adjusting Table Extension

Page 17

Attach Sawdust Chute

1.From among the loose parts find the following:

1Sawdust Chute

2Wing Screw 1/4-20 x 5/8

1Wrench Box 8mm/10mm

1Wrench Hex-“L” 3mm

2.Slide the tab on the bottom side of the dust chute into the slot just below the chute on the left side of the base. Fasten the dust chute on with the 2 wing screws through the slots on both sides of the dust chute.

3.The 3mm hex-L wrench and 8mm open end wrench (supplied with the jointer) used for blade adjustments, can be conveniently stored in the dust chute as shown.

NOTE: If a dust collection system is not in use, simply loosen the two wing screws, lift the bottom of the chute up, out and then slide the dust chute up and retighten the wing screws.

Tool

Storage

Sawdust Chute

Screw Wing 1/4-20 x 5/8

Adjusting Table Extension

The table extension is adjusted at the factory and should not require any additional adjustments. In the event that it shifted during shipping, align it to the outfeed table as fol- lows.

1.Loosen the 2 hex head screws that attach the exten- sion to the outfeed table.

2.Using a straight edge, align the extension to be flush with the outfeed table.

3.Tighten the two screws and recheck the alignment.

Outfeed

Table

Socket Head

Screw

	Extension even with
Extension	outfeed table
Extension

17

Image 17

Contents 235$725·60$18$ Safety Instructions For Jointer/Planer Table of ContentsMajor Hazards Before Using the Jointer/PlanerSafety Labels and Indicators on the Jointer/Planer Inspect Your Workpiece Plan Ahead To Protect Your Eyes, Hands, Face and EarsBefore Leaving the Jointer/Planer Whenever Jointer/Planer Is RunningKeep Children Away Don’t Force ToolGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information General Electrical ConnectionsChanging Motor Voltage Prong Plug Properly Grounded Outlet GroundingExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Serrated Hex Bolt Loose Parts From Hardware PackCabinet and Motor Mount Assembly AssemblySerrated Flange Hex Nut 5/16 Motor Assembly With Switch Install the Leveling FeetMounting the Motor Carriage Head Bolt 16-18 x 1/2Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Installing Handwheel Installing the Pulley GuardSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8Attach Sawdust Chute Adjusting Table ExtensionTool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Outfeed Socket Head Screw Extension even with Outfeed tableAssembly Fence Nut Mount Install Cutter Head GuardAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size NotAdjusting the Leveling Feet Adjusting Guard SpringCutter Head Guard Functional Check Pan Head Screw KnobPage Angle Gauge On-Off SwitchAlignments Cutter Knife Alignment/Adjustments11/16 Wide New Blade Second Cutting Ground Surface Edge Cutter Knife SharpeningOutfeed Table Adjustment Fence Tilt Use and Bevel Stop Adjustment Adjusting Table GibsAngle Gauge Use Stop Screw BarFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Feeding the Workpiece All Operations Always Use Push Blocks When Planing, Beveling Or ChamferingPush blocks and push sticks Plan your workBefore Leaving the jointer/planer Inspect your workpieceDepth of Cut Handwheel Operation Basic Jointer/Planer Cutting OperationsStop Pin Operation Feeding the WorkpieceJointing PlaningBeveling/Chamfering Jointing Without Push BlocksRabbeting Using the Hold-Down/Push-BlocksSupport Long Workpieces Face Rabbet End EdgeSliding Lock Knob Sliding Fence OperationWiring Diagram Maintenance and LubricationMaintenance LubricationTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor 2120 45 46 Repair PartsKey Description Always order by Part Number Not by Key Number DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts Call DAY Satisfaction Guarantee Policy