RIDGID JP0610 manual Repair Parts

Page 38

Repair Parts

Parts List for RIDGID 6-1/8" Jointer/Planer

Model No. JP06101

RIDGID parts are available on-line at www.ridgidparts.com

Figure 2

			3
	29
		31	30		4
			30		4
			31	2
			31
28			1


27			26		6
27


		24	25
	23	24	16
	23		16
21	22				7
			32		7
			32	9	8
				9
16	20				10
17					10
					11
		14	15		12
			15

13 12

Image 38

Contents 235$725·60$18$ Table of Contents Safety Instructions For Jointer/PlanerBefore Using the Jointer/Planer Major HazardsSafety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your WorkpieceKeep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force ToolGlossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet GroundingExtension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex BoltAssembly Cabinet and Motor Mount AssemblyMounting the Motor Install the Leveling FeetSerrated Flange Hex Nut 5/16 Motor Assembly With Switch Carriage Head Bolt 16-18 x 1/2Align Belt Tighten Motor Mount Nuts Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Serr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8Tool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed tableAssemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size NotCutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobPage On-Off Switch Angle GaugeCutter Knife Alignment/Adjustments AlignmentsCutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface EdgeOutfeed Table Adjustment Angle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw BarFence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your workInspect your workpiece Before Leaving the jointer/planerStop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the WorkpieceBeveling/Chamfering PlaningJointing Jointing Without Push BlocksSupport Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End EdgeSliding Fence Operation Sliding Lock KnobMaintenance Maintenance and LubricationWiring Diagram LubricationTrouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Repair Parts 2120 45 46Always order by Part Number Not by Key Number Description Key DescriptionRepair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call

			3
	29
		31	30		4
			30		4
			31	2
			31
28			1


27			26		6
27


		24	25
	23	24	16
	23		16
21	22				7
			32		7
			32	9	8
				9
16	20				10
17					10
					11
		14	15		12
			15

			3
	29
		31	30		4
			30		4
			31	2
			31
28			1


27			26		6
27


		24	25
	23	24	16
	23		16
21	22				7
			32		7
			32	9	8
				9
16	20				10
17					10
					11
		14	15		12
			15

			3
	29
		31	30		4
			30		4
			31	2
			31
28			1


27			26		6
27


		24	25
	23	24	16
	23		16
21	22				7
			32		7
			32	9	8
				9
16	20				10
17					10
					11
		14	15		12
			15