Miller Electric 1251, ICE-100TM manual Symbols And Definitions, I1max, I1eff

Page 13

.A complete Parts List is available at www.MillerWelds.com

SECTION 3 − DEFINITIONS

3-1. Symbols And Definitions

Amperes

Plasma Arc Cutting

Adjust Air/Gas

Low Air Pressure

(PAC)

Pressure

Light

Volts

Increase

No − Do Not Do

Temperature

This

Protective Earth

Single Phase

Constant Current

Voltage Input

(Ground)

Off

Percent

Direct Current

Rated No Load

Primary Voltage

Conventional Load

Line Connection

Voltage (Average)

Voltage

Single Phase Or

I1max

Three Phase Static

Rated Maximum

Rated Welding

Duty Cycle

1/3

Frequency

Supply Current

Current

Converter-

Transformer-

Rectifier

Degree Of

Loose Shield Cup

Input

Hertz

Protection

I1eff

Suitable for Some

Power Rating,

Maximum Effective

power factor

Hazardous

Product Of Voltage

Supply Current

Locations

And Current (KVA)

OM-201 872 Page 9

Image 13

Contents Processes OM-201 872DDescription File Plasma CuttersFrom Miller to You Table of Contents − Maintenance & Troubleshooting Marks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosionFlying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulierLE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Organes Mobiles peuvent provoquer des blessures DES Pieces Chaudes peuvent pro- voquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OUInformation sur les champs électromagnétiques Principales normes de sécuritéLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaques− Definitions Symbols And DefinitionsI1max I1effSpecifications − InstallationCutting Speed Duty Cycle and OverheatingMovement Do not move or operate unit where it could tip Dimensions And WeightSelecting a Location Connecting And Disconnecting Torch Connecting Work Clamp and Gas/Air SupplyHz Three Phase Input Voltage Electrical Service GuideHz Three Phase Min Grounding Conductor Size In AWGExtension Cord Data = GND/PE Earth Ground Connecting 3-Phase Input PowerReinstall power panel Three-Phase Power ConnectionClose panel opening if no connections are made to generator − Operation Power Switch OM-201 872Controls Trigger Safety Lock Setting Gas/Air PressureSetting Gas/Air Pressure 90-120 psiPlasma Cutting System Practices Pilot arc starts immediately when trigger is pressedMaintain approximately a 90 angle to Workpiece surface for proper cutting resultsSparks go thru metal Sequence Of Cutting OperationSequence Of Gouging Operation Set Mode switch to GougeHold torch at approximately Angle to workpiece Consumables Storage Compartment Sequence Of Piercing OperationRemote Control Cable Functions Remote Control Receptacle− Mechanized Operation ICE-100TM Mounting PositionRemote Control Cable Okay To Move Turn off and disconnect input power+24 Volts DC Hot Contacts For Relay Operation White Remote RedStart Black +24 VDC Green RelayRemote Start Output Turn off Input powerWhite Red Green Black Remote Control Cable Shield Sense Tab Remote Voltage Sense ConnectionTools Needed 15/16 Amp Machine Torch Shielded Consumables Cut ChartsMild Steel Stainless089 105 486 140388 12.7 524 991706 15,926 502 12,751353 600835 16,256 221464 15,037 335Deflector Retaining Cap Tip Electrode Swirl Ring Amp Machine Torch Extended ConsumablesArc Voltage 12.7 397 863 160 064 106140 556 120 12.7 032114 896 610 15,494 385057 214 435 135Routine Maintenance − Maintenance & TroubleshootingChecking Shield Cup Shutdown System Trouble LightsChecking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch partsChecking Or Replacing Filter Element Trouble Remedy Troubleshooting Power SourceClean Troubleshooting TorchArc goes on and off while cutting Arc goes out while cuttingCircuit Diagram For Power Source − Electrical Diagram201 858-A Recommended Spare Parts − Parts ListRecommended Spare Parts 215 606 Clip, retaining40A Drag Shield60A Ring80A Ring Shield Sense Tab* Retaining Cap Tip ElectrodeDeflector Retaining Cap Tip 804 036-A Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

ICE-100T, 1251, ICE-100TM specifications

Miller Electric has long been a trusted name in the welding industry, and their range of inverter-powered welding machines continues to set benchmarks for performance and reliability. Among their most notable offerings are the ICE-100TM, 1251, and ICE-100T models, which have been engineered to meet the demands of both professional and DIY welders.

The ICE-100TM is particularly celebrated for its cutting-edge technology that maximizes efficiency and versatility. This machine features an advanced inverter design that allows for a compact form factor while maintaining high output performance. The ICE-100TM is capable of both MIG and TIG welding, making it a dual-purpose device that can handle a variety of materials, including steel, aluminum, and stainless steel. With precise control over heat input and an adjustable arc, welders can easily tailor their settings for different applications.

The 1251 model builds upon the foundation of the ICE-100TM, introducing a host of enhancements that improve user experience. With a more robust power output, the 1251 can handle thicker materials with ease, while its intuitive interface allows for quick adjustments, ensuring optimal performance in diverse welding conditions. This model also integrates advanced safety features like thermal overload protection, safeguarding both the machine and the user during intensive projects.

The ICE-100T is another standout model, designed for those who prioritize portability without sacrificing power. Weighing significantly less than traditional welding machines, the ICE-100T is engineered for ease of transport and convenience on the job site. Its user-friendly controls make it ideal for welders of all skill levels, while its durable design ensures that it can withstand tough working environments.

All three models incorporate Miller Electric's proprietary Auto-Set technology. This feature automatically regulates parameters such as voltage and wire feed speed based on the material being welded, minimizing the setup time and enhancing overall weld quality.

In terms of characteristics, these machines boast a rugged construction designed for long-lasting performance. Their compact designs coupled with lightweight materials facilitate mobility, making them suitable for fieldwork as well as workshop settings. Additionally, their low energy consumption aligns with modern sustainability practices, making them not only efficient but environmentally friendly.

In summary, the Miller Electric ICE-100TM, 1251, and ICE-100T welding machines represent the forefront of welding technology with their innovative features, adaptability, and reliable performance. These models offer a compelling choice for professional welders and hobbyists alike, ensuring they can tackle a wide range of welding tasks with confidence and efficiency.