Miller Electric MOG-300, MOG-350 Female Camlok Connector Assembly, Male Camlok Connector Assembly

Page 18

3-5. Female Camlok Connector Assembly

12

1 in

(26 mm)

6

5

Tools Needed:

7/32 in

		1	Weld Input Cable
		Strip insulation as shown.
		2	Copper Strip (Two Included)
4		3	Connector Body
		Wrap strip around bare weld cable
		(use two on small diameter cable),
	3	and insert into connector body.
	3
		4	Setscrew

Tighten setscrew against copper strip.

5Handle

6Pin

Slide handle over connector body so holes align; secure by tapping pin into place.

sb6.6* – ST-159 028

3-6. Male Camlok Connector Assembly

12

1 in

(26 mm)

6

5

1 Weld Output Cable

Strip insulation as shown.

2Copper Strip

3Connector Body

Wrap strip around bare weld cable

4(use two on small diameter cable), and insert into connector body.

4 Setscrew

3

Tighten setscrew against copper strip.

5Handle

6Pin

Slide handle over connector body so holes align; secure by tapping pin into place.

Tools Needed:

7/32 in

sb6.4* 11/92 – ST-155 015

OM-808 Page 14

Image 18

Contents OM-808 ProcessesDescription From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersUN Choc É Lectrique peut tuer Signification des symbolesConsignes DE Securite Lire Avant Utilisation LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe ’EMPLOI Excessif peut Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques Specifications Resistance GridGrid Rack Installation Typical Multiple Operator System Component RelationshipsTurn Off welding power source Before moving grid or rack Resistance GridMulti-Grid Rack Tools Needed Weld Input/Output Cables For Multi-Grid Rack Female Camlok Connector Assembly Male Camlok Connector Assembly150 ft 200 ft 250 ft 300 ft 350 ft Weld Cable SizeOptional Remote Receptacle Information And Connections 45 m 60 m 70 m 90 m 105 m 120 mSafety Equipment OperationControls Dual Model Shown Optional Polarity Switch Arcing can damage switchWork Clamp Amperage Controls Paralleling Switch Dual Models Only Optional Remote Grid Amperage ControlTurn Off all power before maintaining Maintenance & TroubleshootingRoutine Maintenance Months Sequence Of Shielded Metal Arc Welding SmawTroubleshooting Overload ProtectionElectrical Diagrams Circuit Diagram For 300 Ampere ModelCircuit Diagram For 400 Ampere Model Circuit Diagram For 250/250 Ampere Model Circuit Diagram For 350/350 Ampere Model Parts List Main AssemblyDia Part Panel, Front w/Components Nameplate Resistor Assembly, Current 049 BUS BAR, interconnecting resistors MOG-Pak 6 APR MOG-Pak 2, 4 Optional EquipmentRemote Control Service SupportOwner’s Record Miller Electric Mfg. Co