Appliance Preparation | Hearth and Home Technologies CERONA-42

7 Appliance Preparation

A.Removing Non-combustible Facing Mate- rial Assembly

The non-combustible assembly is located on the back of appliance (see Figure 7.1).

CAUTION

Handle with care.

•Non-combustible material may be damaged if dropped.

•Hold non-combustible pieces in place.

•Remove and save two screws from upper brackets (see Figure 7.1).

•Remove non-combustible pieces.

•Remove and save three screws from lower bracket (see Figure 7.1).

•Discard brackets.

•Replace screws in holes where these pieces were attached to appliance.

Remove screws

from upper bracket.

Lower

Bracket

Figure 7.1 Non-Combustible Facing Material Assembly

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

21

Image 21

Hearth and Home Technologies CERONA-42 Appliance Preparation, Removing Non-combustible Facing Mate- rial Assembly

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Read all of the instructions before starting the insta Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components Vent Table Key Vent Information and DiagramsMeasuring Standards Use of Elbows Vent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Top Vent Vertical Termination Straight up Vertical Venting Top Vent Horizontal Termination Three ElbowsV1 = 50 ft. Max .2 m 152 mm 914 mm 305 mm 610 mm 10 ft 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Installing the Ceiling Firestop Installing Attic ShieldVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe Sections Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Securing the Vent Sections Disassembly of Vent SectionsVertical Sections Horizontal Sections Installing the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Heat shield DVP-HSM-B must be used ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Gas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Electrical Information For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Finishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material OptionsFinishing Material Thickness greater than 1-1/4 inch Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Clean the Appliance Appliance SetupAccessories Ember Placement Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Glass Assembly Air Shutter SettingGrilles and Trim Operating Instructions Before Lighting ApplianceThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI Ignition Frequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Intelliﬁre Ignition SystemSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsModel Cerona-36 Model Cerona-42 DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Log Set Assembly Service PartsPart number list on following Service Parts List StockedAt Depot IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information