Finishing Material Options | Hearth and Home Technologies CERONA-42

C. Finishing Material Options

Finishing Material Thickness from 3/4 in. to 1-1/4 in.

Finishing material within this thickness range can be brought to 1/2 inch behind the door top and sides. These non-combustible ﬁnishing materials must never overlap or obstruct the air outlet/inlet grille areas.

	NON-COMBUSTIBLE FINISHING MATERIAL
HEADER	(INSTALLED OVER NON-COMBUSTIBLE
HEADER	FACING MATERIAL)

B

1IN.

(25 mm)

A

			A	B
	Cerona-36	in.	43-5/8	50-3/16
	Cerona-36	mm	1108	1275
		mm	1108	1275
	Cerona-42	in.	50-5/8	54-3/8
	Cerona-42	mm	1286	1381
		mm	1286	1381

Non-combustible facing material is supplied with this appliance. This material extends from the header to one inch above the appliance bottom and from framing stud to framing stud.

Figure 11.5

IMPORTANT INSTALLATION

Note: Please note that there are four holes or dots on the template to assist in positioning the template. These holes or dots should line up with the door mounting holes on the unit to ensure proper placement of the door after ﬁnishing materials are installed.

Finishing Material Thickness greater than 1-1/4 inch

A steel template (Cerona-36 Template or Cerona-42 Tem- plate) is available for purchase to use instead of construct- ing a template.

R I

ØH

A

G

B

C

F

D

E

A

B

C

D

E

Cerona-36

in.

34-1/2

23-9/16

5-3/16

1-1/4

38

mm

876

598

132

32

965

Cerona-42

in.

38-7/8

25-1/4

3-5/8

2-5/8

46-1/4

mm

987

641

92

67

1175

F

G

H

I

Cerona-36

in.

1-1/4

28-13/16

3/8

34-5/8

mm

32

732

10

879

Cerona-42

in.

2-5/8

31-7/16

3/8

39-5/8

mm

67

799

10

1006

Figure 11.6 Facing Template Dimensions

Mounting stone eye brow: ATRIMSTONE-36, ATRIMSTONE-42

Note: When mounting ATRIMSTONE-36 OR ATRIMSTONE- 42 you must install template or front to insure proper positioning. Failure to do so will result in the front not ﬁtting (see Figure 11.5).

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

37

Image 37

Hearth and Home Technologies CERONA-42 Finishing Material Options, Finishing Material Thickness from 3/4 in. to 1-1/4

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Read all of the instructions before starting the insta Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Vent Table Key Vent Information and DiagramsMeasuring Standards Use of Elbows Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows Top Vent Vertical Termination Straight up Vertical Venting Top Vent Horizontal Termination Three ElbowsV1 = 50 ft. Max .2 m 152 mm 914 mm 305 mm 610 mm 10 ft 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Installing Attic Shield Installing the Ceiling FirestopVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe Sections Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Securing the Vent Sections Disassembly of Vent SectionsVertical Sections Horizontal Sections Installing the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Heat shield DVP-HSM-B must be used ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Fuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Electrical Information For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Finishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material OptionsFinishing Material Thickness greater than 1-1/4 inch Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Clean the Appliance Appliance SetupAccessories Ember Placement Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Air Shutter Setting Glass AssemblyGrilles and Trim Before Lighting Appliance Operating InstructionsThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI Ignition Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Intelliﬁre Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramModel Cerona-36 Model Cerona-42 DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Service Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information