Service Parts List | Hearth and Home Technologies CERONA-42 specs

Service Parts List

CERONA-36

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
	Log Set Assembly		LOGS-CERONA36	Y
1	Log 1		SRV2106-701
2	Log 2		SRV2106-703
3	Log 3		SRV2106-705
4	Log 4		SRV2106-704
5	Log 5		SRV2106-702
6	Log 6		SRV2106-706
7	Top Header Heat Shield		2106-144
8	Bottom Header Heat Shield		2106-145
9	Non-Combustible Board Assembly		2106-030
10	Burner NG, LP		2106-003	Y
11	Grate Assembly		2106-006
12	Glass Door Assembly		GLA-CERONA36	Y
13	Fan Kit		GFK-160A
14	Junction Box		4021-013	Y
	Control Box	Pre Sn #0021358898	2106-025	Y
	Control Box	Post Sn #0021359350	WSK-MLT
		Post Sn #0021359350	WSK-MLT
	Fiber Patch Kit		SRV-PACK
	Fiberglass Rope		060-455
	Glass Latch Assembly		386-122A	Y
	Mineral Wool		050-721
	On/Off Rocker Switch		060-521A	Y
	Screw, Bag of 32 ea.		2062-110-23	Y
	Solenoid - 110 Volt Hi/Lo		2101-029	Y
	Touch Up Kit-Fiber Box		CERONA-PAINT
	Touch Up Paint-Metal		TUP-GBK-12
	Vermiculite Embers		MYSTIC-EMBERS
	Vertical Restrictor		2106-141
	Wall Control Assembly		2106-072	Y
	Wires, 2 in Male to Male		2012-206	Y
	Wire, Wall Switch		2095-550	Y

	Conversion Kit NG		N/A
	Conversion Kit LP		LPK-CERONA36	Y
	Pilot Oriﬁce NG		593-528	Y
	Pilot Oriﬁce LP		593-527	Y
	Regulator NG		NGK-DXV	Y
	Regulator LP		LPK-DXV	Y

Additional service part numbers appear on following page.

58	Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

Image 58

Hearth and Home Technologies CERONA-42 owner manual Service Parts List, Stocked, At Depot

Contents

Models What to do if you smell gas Homeowner Reference Information Model Number Serial Number Table of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Tools and Supplies Needed Installation to ensure maximum safety and beneﬁtGetting Started Read all of the instructions before starting the insta Inspect Firebox Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Mantel Projections 724 425 406 279 Hearth Extension Dimensions Hearth Extension Termination Locations Vent Termination Minimum Clearances Alcove Applications Minimum Clearances for Termination To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Measuring Standards Vent Information and DiagramsVent Table Key Use of Elbows Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows V1 = 50 ft. Max .2 m Top Vent Horizontal Termination Three ElbowsTop Vent Vertical Termination Straight up Vertical Venting 152 mm 914 mm 305 mm 610 mm 10 ft Top Vent Horizontal Termination Two Elbows 305 mm 610 mm 914 mm 10 ft Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Installing Attic Shield Installing the Ceiling FirestopVertical Penetration Framing Removing Non-combustible Facing Mate- rial Assembly Appliance Preparation Installing Non-combustible Facing Material Securing and Leveling the Appliance Installing Flue Restrictors Complete Installation of Non-combustible Facing Material Attaching Vent to the Firebox Assembly Installing Vent PipeAssembly of Vent Sections Assembling Pipe Sections Assembling Minimum Installations MI Sections Assembling DVP-12A Slip Sections Vertical Sections Disassembly of Vent SectionsSecuring the Vent Sections Horizontal Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Heat shield DVP-HSM-B must be used Installing Roof Flashing and Vertical Ter- mination Cap ﬂue of the pipe see Figure Assembling and Installing Storm Collar 18 Assembling the Storm Collar Around the Pipe Fuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Connecting to the Appliance Recommendation for WireIntelliﬁre Ignition System Wiring Electrical Information Junction Box Installation For units Without factory installed Rocker Switch Step Finishing Facing Material Non-combustible Facing Material Finishing Material Thickness greater than 1-1/4 inch Finishing Material OptionsFinishing Material Thickness from 3/4 in. to 1-1/4 Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Accessories Appliance SetupClean the Appliance Ember Placement Log Assembly LOGS-Cerona36 Positioning the Logs Model Cerona-36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Air Shutter Setting Glass AssemblyGrilles and Trim Before Lighting Appliance Operating InstructionsThis appliance has an Intelliﬁre ignition system Lighting Appliance IPI Ignition Final inspection by Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Intelliﬁre Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing Appliance Inspect Maintenance Tasks Doors, Surrounds Reference Materials Appliance Dimension DiagramModel Cerona-36 Model Cerona-42 Vent Components Diagrams DVP vent components DVP-TRAP COOL-ADD Not for use with these models Service Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot IPI Valve Assembly CERONA-42 LOGS-CERONA42 Touch UP Paint -Fiber box IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information