LOGS-CERONA42 | Hearth and Home Technologies CERONA-42 instruction

Service Parts List

CERONA-42

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
	Log Set Assembly		LOGS-CERONA42	Y
1	Log 1		SRV2107-701
2	Log 2		SRV2107-702
3	Log 3		SRV2107-703
4	Log 4		SRV2107-704
5	Log 5		SRV2107-705
6	Log 6		SRV2107-706
7	Top Header Heat Shield		2107-144
8	Bottom Header Heat Shield		2107-145
9	Non-Combustible Board		2107-030
10	Burner NG, LP		2107-003	Y
11	Grate Assembly		2106-006
12	Glass Door Assembly		GLA-CERONA42	Y
13	Fan Kit		GFK-160A
14	Junction Box		4021-013	Y
	Control Box	Pre SN #0021358908	2106-025	Y
	Control Box	Post Sn #0021359354	WSK-MLT
		Post Sn #0021359354	WSK-MLT
	Fiber Patch Kit		SRV-PACK
	Fiberglass Rope		060-455
	Glass Latch Assembly		386-122A	Y
	Mineral Wool		050-721
	On/Off Rocker Switch		060-521A	Y
	Screw Bag (23 ea)		2062-110-23	Y
	Solenoid - 110 Volt Hi/Lo		2101-029	Y
	Touch Up Paint		TUP-GBK-12
	Touch UP Paint -Fiber box		CERONA-PAINT
	Vermiculite Embers		MYSTIC-EMBERS
	Vertical Restrictor		2106-141
	Wall Control Assembly		2106-072	Y
	Wires, 2 in Male to Male		2012-206
	Wire, Wall Switch		2095-550	Y

	Conversion Kit NG		N/A
	Conversion Kit LP		LPK-CERONA42	Y
	Pilot Oriﬁce NG		593-528	Y
	Pilot Oriﬁce LP		593-527	Y
	Regulator NG		NGK-DXV	Y
	Regulator LP		LPK-DXV	Y

Additional service part numbers appear on following page.

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

61

Image 61

Hearth and Home Technologies CERONA-42 owner manual LOGS-CERONA42, Touch UP Paint -Fiber box

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Read all of the instructions before starting the insta Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Vent Table Key Vent Information and DiagramsMeasuring Standards Use of Elbows Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows Top Vent Vertical Termination Straight up Vertical Venting Top Vent Horizontal Termination Three ElbowsV1 = 50 ft. Max .2 m 152 mm 914 mm 305 mm 610 mm 10 ft 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Installing Attic Shield Installing the Ceiling FirestopVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe Sections Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Securing the Vent Sections Disassembly of Vent SectionsVertical Sections Horizontal Sections Installing the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Heat shield DVP-HSM-B must be used ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Fuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Electrical Information For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Finishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material OptionsFinishing Material Thickness greater than 1-1/4 inch Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Clean the Appliance Appliance SetupAccessories Ember Placement Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Air Shutter Setting Glass AssemblyGrilles and Trim Before Lighting Appliance Operating InstructionsThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI Ignition Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Intelliﬁre Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramModel Cerona-36 Model Cerona-42 DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Service Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information