Inspect Firebox | Hearth and Home Technologies CERONA-42 specification

D. Inspect Firebox

Surface cracking or crazing of ﬁrebrick material is normal and expected. The following types of cracks are acceptable and do not require replacement of the unit or the ﬁrebox:

•Cracks that do not propagate entirely thru the material.

•Light fracture lines or “spider-webbing” on the surface of the material.

•Cracks that are less than 1/32 in. wide and less than 3 in. long.

•If cosmetically unacceptable, such cracks may be repaired with the SRV-PACK service kit. See Service Parts List.

Cracks that are unacceptable:

•Cracks greater than 1/32 in. wide and 3 in. long are at risk of growing.

•Cracks that penetrate entirely through the firebrick material.

Inspection for cracking should be run when the appliance is cool. Cracks tend to close as the appliance heats up.

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

7

Image 7

Hearth and Home Technologies CERONA-42 owner manual Inspect Firebox

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Read all of the instructions before starting the insta Installation to ensure maximum safety and beneﬁtGetting Started Tools and Supplies Needed Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Use of Elbows Vent Information and DiagramsVent Table Key Measuring Standards Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows 152 mm 914 mm 305 mm 610 mm 10 ft Top Vent Horizontal Termination Three ElbowsTop Vent Vertical Termination Straight up Vertical Venting V1 = 50 ft. Max .2 m 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Installing Attic Shield Installing the Ceiling FirestopVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembling Pipe Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to the Firebox Assembly Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Horizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat shield DVP-HSM-B must be used Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Heat Shield Requirements for Horizontal Termination ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Fuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Electrical Information Recommendation for WireIntelliﬁre Ignition System Wiring Connecting to the Appliance For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 Finishing Material OptionsFinishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material Thickness greater than 1-1/4 inch 10 Fireplace sitting on combustible surface Ember Placement Appliance SetupClean the Appliance Accessories Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Air Shutter Setting Glass AssemblyGrilles and Trim Before Lighting Appliance Operating InstructionsThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI Ignition Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Intelliﬁre Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramModel Cerona-36 Model Cerona-42 DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Service Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information