Vent Components Diagrams | Hearth and Home Technologies CERONA-42

B. Vent Components Diagrams

		Pipe	Effective Length		10-1/2 in.
	Effective	Pipe	Inches	Millimeters	(267 mm)	45°
	Effective		Inches	Millimeters	(267 mm)	45°
	Height/Length	DVP4	4	102
		DVP6	6	152
		DVP12	12	305	4-7/8 in.
		DVP24	24	610	( 276 mm)
		DVP24	24	610		10-7/8 in.
		DVP36	36	914		10-7/8 in.
	DVP Pipe (see chart)	DVP36	36	914		(276 mm)
	DVP Pipe (see chart)	DVP48	48	1219	DVP45 (45 Elbow)°
		DVP48	48	1219
		DVP6A	3 to 6	76 to 152
		DVP6A	3 to 6	76 to 152
		DVP12A	3 to 12	76 to 305
		DVP12MI	3 to 12	76 to 305
		DVP24MI	3 to 24	76 to 610
						11-3/8 in.
						(289 mm)
	10 in.
	(254 mm)	10 in.		1 in.
		(254 mm)		1 in.
		(254 mm)		(25 mm)
				(25 mm)
						7-3/8 in.
	24 in.					(187 mm)
	24 in.
	(610 mm)					1-1/4 in. (32 mm)
						1-1/4 in. (32 mm)
					9-1/4 in.
					(235 mm)	1/2 in. TYP
					13-1/4 in.	(13 mm)
					13-1/4 in.
					(337 mm)
	DVP-AS (Attic Shield)	DVP-FS (Ceiling Firestop)			DVP90ST (90° Elbow)
					DVP90ST (90° Elbow)
					12 in.	1 in.
					(305 mm)	(25 mm)
	10 in.	1- 1/2 in.				8 in.
	10 in.	1- 1/2 in.				(203 mm)
	(254 mm)	(38 mm)		14 in.
				14 in.
	UP			(356 mm)
	UP
	5 in.	12 in.
	(127 mm)	(305 mm)
					6 in.
					(152 mm)
	DVP-HVS (Vent Support)				DVP-WS (Wall Shield Firestop)
	Figure 16.2 DVP vent components
		Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08				53

Image 53

Hearth and Home Technologies CERONA-42 owner manual Vent Components Diagrams, DVP vent components

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Read all of the instructions before starting the insta Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications Continue Adding Vent Components Install Support BracketsTo Install the Heat Shield Vent Table Key Vent Information and DiagramsMeasuring Standards Use of Elbows Two Elbows Vent DiagramsTop Vent Horizontal Termination One Elbow Top Vent Vertical Termination Straight up Vertical Venting Top Vent Horizontal Termination Three ElbowsV1 = 50 ft. Max .2 m 152 mm 914 mm 305 mm 610 mm 10 ft 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Vertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe Sections Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Securing the Vent Sections Disassembly of Vent SectionsVertical Sections Horizontal Sections Installing the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Heat shield DVP-HSM-B must be used ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Gas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Electrical Information For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Finishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material OptionsFinishing Material Thickness greater than 1-1/4 inch Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Clean the Appliance Appliance SetupAccessories Ember Placement Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Grilles and Trim Glass AssemblyAir Shutter Setting This appliance has an Intelliﬁre ignition system Operating InstructionsBefore Lighting Appliance Final inspection by Lighting Appliance IPI Ignition After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Model Cerona-36 Model Cerona-42 Appliance Dimension DiagramReference Materials DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Part number list on following Log Set AssemblyService Parts At Depot Service Parts ListStocked IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information