Cool-Add | Hearth and Home Technologies CERONA-42 manual

B. Vent Components Diagrams (continued)

			31 in.
			(787 mm)
13-1/4 in.
(367 mm)		24-5/8 in.
		(625 mm)
24-5/8 in.	27-1/2 in.
(625 mm)	(127 mm)			13-1/4 in.
				13-1/4 in.
			(367 mm)
RF6M			RF12M
Roof Flashing Multi-pak			RF12M
Roof Flashing Multi-pak		Roof Flashing Multi-pak
		Roof Flashing Multi-pak
13-3/4 in.	5 in.		11-7/8 in.	5 in.
(349 mm)	(127 mm)		(302 mm)	(127 mm)
13-3/4 in.		13-7/8 in.
13-3/4 in.		(352 mm)
(349 mm)		(352 mm)
(349 mm)
BEK			DVP-BEK2
Trap Cap Brick Extension		DVP-HPC Cap Brick Extension
	11-5/8 in.
	(295 mm)
7-1/8 in.		12-1/8 in.
7-1/8 in.		(308 mm)
(181 mm)		(308 mm)
(181 mm)
	5-3/4 in.
	(146 mm)
		COOL-ADD
		Cap Shield
		13-7/8 in.	9-1/2 in.
		(352 mm)	(241 mm)
		14 in.
DVP-TRAPFL		(356 mm)
DVP-TRAPFL
Flashing		DRC-RADIUS
		DRC-RADIUS
Figure 16.4 DVP vent components		Cap Shield
Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08				55

Image 55

Hearth and Home Technologies CERONA-42 owner manual Cool-Add

Contents

What to do if you smell gas Models Model Number Serial Number Homeowner Reference Information Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Read all of the instructions before starting the insta Installation to ensure maximum safety and beneﬁtGetting Started Tools and Supplies Needed Inspect Firebox Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase 724 425 406 279 Mantel Projections Hearth Extension Hearth Extension Dimensions Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Alcove Applications To Install the Heat Shield Install Support BracketsContinue Adding Vent Components Use of Elbows Vent Information and DiagramsVent Table Key Measuring Standards Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows 152 mm 914 mm 305 mm 610 mm 10 ft Top Vent Horizontal Termination Three ElbowsTop Vent Vertical Termination Straight up Vertical Venting V1 = 50 ft. Max .2 m 305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two Elbows Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Installing Attic Shield Installing the Ceiling FirestopVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly Securing and Leveling the Appliance Installing Non-combustible Facing Material Complete Installation of Non-combustible Facing Material Installing Flue Restrictors Assembling Pipe Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to the Firebox Assembly Assembling DVP-12A Slip Sections Assembling Minimum Installations MI Sections Horizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat shield DVP-HSM-B must be used Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Heat Shield Requirements for Horizontal Termination ﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap 18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm Collar Fuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Electrical Information Recommendation for WireIntelliﬁre Ignition System Wiring Connecting to the Appliance For units Without factory installed Rocker Switch Junction Box Installation Step Finishing Non-combustible Facing Material Facing Material Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 Finishing Material OptionsFinishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material Thickness greater than 1-1/4 inch 10 Fireplace sitting on combustible surface Ember Placement Appliance SetupClean the Appliance Accessories Positioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Air Shutter Setting Glass AssemblyGrilles and Trim Before Lighting Appliance Operating InstructionsThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI Ignition Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Intelliﬁre Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Doors, Surrounds Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramModel Cerona-36 Model Cerona-42 DVP vent components Vent Components Diagrams DVP-TRAP COOL-ADD Not for use with these models Service Parts Log Set AssemblyPart number list on following Stocked Service Parts ListAt Depot IPI Valve Assembly CERONA-42 Touch UP Paint -Fiber box LOGS-CERONA42 IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information