IPI Valve Assembly | Hearth and Home Technologies CERONA-42 specification

Service Parts	CERONA-42

Valve Assembly Diagram/ Parts List	Beginning Manufacturing Date: June 2006
	Ending Manufacturing Date: ______

IPI Valve Assembly			1			13
IPI Valve Assembly						13
			2
					3	12
						12
				5		4
				5
6
8	7
	7
	9
		10				11
		10

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
1	Pilot Bracket		2106-135
2	Pilot Assembly NG		2106-009	Y
2	Pilot Assembly LP		2106-008	Y
	Pilot Assembly LP		2106-008	Y
3	Shutter Bracket Assembly (NG)		2106-010
3	Shutter Bracket Assembly (LP)		2106-071
	Shutter Bracket Assembly (LP)		2106-071
4	Shutter Sleeve		2026-130
5	Collar 4”		2081-140
6	Flex Ball Valve Assembly		302-320A	Y
7	Module Wire Assembly		593-590A	Y
8	Battery Pack		593-594A	Y
9	Module		593-592	Y
10	Valve NG		750-500	Y
10	Valve LP		750-501	Y
	Valve LP		750-501	Y
11	Valve Bracket		2106-107
12	Flexible Gas Connector		530-302A	Y
13	Oriﬁce NG (#29C)		582-829	Y
13	Oriﬁce LP (#48C)		582-848	Y
	Oriﬁce LP (#48C)		582-848	Y

62	Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. H • 11/08

Image 62

Hearth and Home Technologies CERONA-42 owner manual IPI Valve Assembly

Contents

Models What to do if you smell gas Homeowner Reference Information Model Number Serial Number Table of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Tools and Supplies Needed Installation to ensure maximum safety and beneﬁtGetting Started Read all of the instructions before starting the insta Inspect Firebox Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Mantel Projections 724 425 406 279 Hearth Extension Dimensions Hearth Extension Termination Locations Vent Termination Minimum Clearances Alcove Applications Minimum Clearances for Termination Continue Adding Vent Components Install Support BracketsTo Install the Heat Shield Measuring Standards Vent Information and DiagramsVent Table Key Use of Elbows Two Elbows Vent DiagramsTop Vent Horizontal Termination One Elbow V1 = 50 ft. Max .2 m Top Vent Horizontal Termination Three ElbowsTop Vent Vertical Termination Straight up Vertical Venting 152 mm 914 mm 305 mm 610 mm 10 ft Top Vent Horizontal Termination Two Elbows 305 mm 610 mm 914 mm 10 ft Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Vertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Removing Non-combustible Facing Mate- rial Assembly Appliance Preparation Installing Non-combustible Facing Material Securing and Leveling the Appliance Installing Flue Restrictors Complete Installation of Non-combustible Facing Material Attaching Vent to the Firebox Assembly Installing Vent PipeAssembly of Vent Sections Assembling Pipe Sections Assembling Minimum Installations MI Sections Assembling DVP-12A Slip Sections Vertical Sections Disassembly of Vent SectionsSecuring the Vent Sections Horizontal Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Heat shield DVP-HSM-B must be used Installing Roof Flashing and Vertical Ter- mination Cap ﬂue of the pipe see Figure Assembling and Installing Storm Collar 18 Assembling the Storm Collar Around the Pipe Gas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Connecting to the Appliance Recommendation for WireIntelliﬁre Ignition System Wiring Electrical Information Junction Box Installation For units Without factory installed Rocker Switch Step Finishing Facing Material Non-combustible Facing Material Finishing Material Thickness greater than 1-1/4 inch Finishing Material OptionsFinishing Material Thickness from 3/4 in. to 1-1/4 Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-42 10 Fireplace sitting on combustible surface Accessories Appliance SetupClean the Appliance Ember Placement Log Assembly LOGS-Cerona36 Positioning the Logs Model Cerona-36 Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. H 11/08 Model Cerona-42 Step Grilles and Trim Glass AssemblyAir Shutter Setting This appliance has an Intelliﬁre ignition system Operating InstructionsBefore Lighting Appliance Lighting Appliance IPI Ignition Final inspection by After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing Appliance Inspect Maintenance Tasks Doors, Surrounds Model Cerona-36 Model Cerona-42 Appliance Dimension DiagramReference Materials Vent Components Diagrams DVP vent components DVP-TRAP COOL-ADD Not for use with these models Part number list on following Log Set AssemblyService Parts At Depot Service Parts ListStocked IPI Valve Assembly CERONA-42 LOGS-CERONA42 Touch UP Paint -Fiber box IPI Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information