Miller Electric PipePro Dual manual Miller Electric Mfg. Co, Transportation Department

Page 48

Owner’s Record

Please complete and retain with your personal records.

Model Name	Serial/Style Number

Purchase Date	(Date which equipment was delivered to original customer.)

Distributor

Address

City

State	Zip

For Service

Contact a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:	Welding Supplies and Consumables
	Options and Accessories
	Personal Safety Equipment
	Service and Repair
	Replacement Parts
	Training (Schools, Videos, Books)
	Technical Manuals (Servicing Information
	and Parts)
	Circuit Diagrams
	Welding Process Handbooks
	To locate a Distributor or Service Agency visit
	www.millerwelds.com or call 1-800-4-A-Miller

Contact the Delivering Carrier to:	File a claim for loss or damage during
	shipment.
	For assistance in filing or settling claims, contact
	your distributor and/or equipment manufacturer’s
	Transportation Department.
PRINTED IN USA	♥ 2008 Miller Electric Mfg. Co. 2008−01

Miller Electric Mfg. Co.

An Illinois Tool Works Company

1635 West Spencer Street

Appleton, WI 54914 USA

International Headquarters−USA

USA Phone: 920-735-4505 Auto-Attended

USA & Canada FAX: 920-735-4134

International FAX: 920-735-4125

European Headquarters −

United Kingdom

Phone: 44 (0) 1204-593493

FAX: 44 (0) 1204-598066

www.MillerWelds.com

Image 48

Contents OM-230 009F ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-230 009 Disconnect input plug or power before working on machine − DefinitionsDrive rolls can injure fingers Keep your head out of the fumesSymbols And Definitions Specifications− Introduction Rating− Installation Typical Connection Diagram For MIG EquipmentTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Plug Information Pin Pin InformationInstalling And Threading Welding Wire Setting Internal DIP Switches Current Detect Override OFF Factory Default S1-1 And S1-2Right Side Motor Control Board PC1 Left Side Motor PC101 Automatic Run-In OFF S1-1 And S1-2Display Board DIP Switch Settings Factory Set Default Settings For DIP Switches S1 And S4Tools Needed Remove wrapper DIP Switch S1 And S4 Power Switch Left/Right Select Switch− Operation Operational TermsJog/Purge Switch Front Panel ControlsSee Time secProgram Push Button Upper DisplayUpper Display Upper Display Push ButtonSetup Push Button Lower DisplayAdjust Control Welding Sequence DiagramSequence Push Button WeldAuxiliary Menus Wire Feed Speed Units When the Setup button is pressed again, the menu repeatsRange Locks Software Revision LevelRemote-14 Receptacle Information At the same time, as both− Setting Sequence Parameters − Setting Dual Schedule ParametersOptional Dual Schedule Switch Diagrams Sequence Parameters In a ProgramDiagnostics Indicates a com Indicates a trigger Munication error ErrorLED3-Related Error Indications − Maintenance & Troubleshooting Routine MaintenanceDisconnect power before maintaining = Check ~ = Clean = Replace Reference EveryTroubleshooting Disconnect power before troubleshootingTrouble Remedy Material Thickness Gauge − Electrical Diagram Circuit Diagram229 867-A − Parts List 21 −2Part Description Quantity Control Box GS1,101 219 Drive Assembly, Wire Drive Assembly, Wire -1Item203 Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive Roll Drive KitService Your distributor also givesSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s