Miller Electric PipePro Dual manual Definitions, Drive rolls can injure fingers

Page 15

SECTION 3 − DEFINITIONS

3-1. Warning Label Definitions

ABC

1

1.1

1.2

1.3

2			2.1			2.2			2.3

3

3.1

3.2

3.3

4	4.1
	+	+ +
5	+	6
	+

S-178 936

A.Warning! Watch Out! There are possible hazards as shown by the symbols.

B.Drive rolls can injure fingers.

C.Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear.

1 Electric shock can kill.

1.1Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.

1.2Protect yourself from electric shock by insulating yourself from work and ground.

1.3Disconnect input plug or power before working on machine.

2Breathing welding fumes can be hazardous to your health.

2.1Keep your head out of the fumes.

2.2Use forced ventilation or local exhaust to remove the fumes.

2.3Use ventilating fan to remove fumes.

3Welding sparks can cause explosion or fire.

3.1Keep flammables away from welding. Don’t weld near flammables.

3.2Welding sparks can cause fires. Have a fire extinguisher nearby and have a watch person ready to use it.

3.3Do not weld on drums or any closed containers.

4Arc rays can burn eyes and injure skin.

4.1Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.

5Become trained and read the instructions before working on the machine or welding.

6Do not remove or paint over (cover) the label.

OM-230 009 Page 11

Image 15

Contents File MIG Gmaw OM-230 009FProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- Sion Proposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-230 009 Keep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Drive rolls can injure fingersRating Symbols And DefinitionsSpecifications − IntroductionTypical Connection Diagram For MIG Equipment − InstallationTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Pin Information Pin Plug InformationInstalling And Threading Welding Wire Automatic Run-In OFF S1-1 And S1-2 Setting Internal DIP SwitchesCurrent Detect Override OFF Factory Default S1-1 And S1-2 Right Side Motor Control Board PC1 Left Side Motor PC101Display Board DIP Switch Settings Factory Set Default Settings For DIP Switches S1 And S4Tools Needed Remove wrapper DIP Switch S1 And S4 Operational Terms Power SwitchLeft/Right Select Switch − OperationTime sec Jog/Purge SwitchFront Panel Controls SeeUpper Display Push Button Program Push ButtonUpper Display Upper DisplayLower Display Setup Push ButtonWeld Adjust ControlWelding Sequence Diagram Sequence Push ButtonAuxiliary Menus Software Revision Level Wire Feed Speed UnitsWhen the Setup button is pressed again, the menu repeats Range LocksAt the same time, as both Remote-14 Receptacle InformationSequence Parameters In a Program − Setting Sequence Parameters− Setting Dual Schedule Parameters Optional Dual Schedule Switch DiagramsDiagnostics Indicates a com Indicates a trigger Munication error ErrorLED3-Related Error Indications = Check ~ = Clean = Replace Reference Every − Maintenance & TroubleshootingRoutine Maintenance Disconnect power before maintainingTroubleshooting Disconnect power before troubleshootingTrouble Remedy Material Thickness Gauge Circuit Diagram − Electrical Diagram229 867-A 21 −2 − Parts ListPart Description Quantity Control Box GS1,101 219 Drive Assembly, Wire -1Item Drive Assembly, Wire203 Roll Drive Kit Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll DriveService Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact