Miller Electric PipePro Dual manual Fire or Explosion hazard, Falling Unit can cause injury

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic- ing unit.

DUse only genuine replacement parts from the manufacturer.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can cause injury.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-230 009 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents File MIG Gmaw OM-230 009FProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-230 009 Keep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Drive rolls can injure fingersRating Symbols And DefinitionsSpecifications − IntroductionTypical Connection Diagram For MIG Equipment − InstallationTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Pin Information Pin Plug InformationInstalling And Threading Welding Wire Automatic Run-In OFF S1-1 And S1-2 Setting Internal DIP SwitchesCurrent Detect Override OFF Factory Default S1-1 And S1-2 Right Side Motor Control Board PC1 Left Side Motor PC101Factory Set Default Settings For DIP Switches S1 And S4 Display Board DIP Switch SettingsTools Needed Remove wrapper DIP Switch S1 And S4 Operational Terms Power SwitchLeft/Right Select Switch − OperationTime sec Jog/Purge SwitchFront Panel Controls SeeUpper Display Push Button Program Push ButtonUpper Display Upper DisplayLower Display Setup Push ButtonWeld Adjust ControlWelding Sequence Diagram Sequence Push ButtonAuxiliary Menus Software Revision Level Wire Feed Speed UnitsWhen the Setup button is pressed again, the menu repeats Range LocksAt the same time, as both Remote-14 Receptacle InformationSequence Parameters In a Program − Setting Sequence Parameters− Setting Dual Schedule Parameters Optional Dual Schedule Switch DiagramsIndicates a com Indicates a trigger Munication error Error DiagnosticsLED3-Related Error Indications = Check ~ = Clean = Replace Reference Every − Maintenance & TroubleshootingRoutine Maintenance Disconnect power before maintainingDisconnect power before troubleshooting TroubleshootingTrouble Remedy Material Thickness Gauge Circuit Diagram − Electrical Diagram229 867-A 21 −2 − Parts ListPart Description Quantity Control Box GS1,101 219 Drive Assembly, Wire -1Item Drive Assembly, Wire203 Roll Drive Kit Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll DriveYour distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact
Top Page Image Contents