Miller Electric OM-234 016D manual Connecting Spool Gun To Millermatic 140/180

Page 17

B. Connecting Spool Gun To Millermatic 140/180

6 7

5

1

3

4

2

.Be sure that gun end is tight against drive assembly.

4

4

1Drive Assembly

2Spool Gun

3Gun Securing Knob

4Gun End

Loosen thumbscrew. Insert end through opening until it bottoms against drive assembly. Tighten gun securing knob.

Spool gun must be inserted completely to prevent leakage of shielding gas.

5 Gun Trigger Plug

Insert plug into receptacle, and tighten threaded collar.

6Spool Gun/MIG Gun Switch Place switch in Spool Gun position.

7Polarity Changeover Terminal Block

To make proper polarity connection, see welding power source Owner’s Manual.

Close door.

Incorrect

Exposed O-rings

Correct

Gun Not Seated

will cause shielding

Gun Fully Seated

 

gas leakage.

 

804 984-A / Ref. 801 987

OM-234 016 Page 13

Image 17
Contents OM-234 016D File Wire FeederProcesses DescriptionFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-234 016 Removing MIG Gun From Welding Power Source SpecificationsOperation Connecting Spool Gun To Millermatic 140/180 ModelsTurn Off unit, and disconnect input power Polarity Changeover Terminal Block Close door Connecting Spool Gun To Millermatic 140/180Correct Connecting Spool Gun To Millermatic Passport PlusIncorrect Connecting Spool Gun To Renegade Installing Wire Spool And Threading Welding Wire Spool Gun Operation On Millermatic 140/180 Models Controls For Millermatic 140/180 ModelsExample .030 diameter wire, welding 18 ga. material Weld Parameter Chart For Millermatic 140 Model w/Auto−SetEExample 4 Refer to chart below to select Voltage and Wire Speed basedNumber on right Slash is Wire Selecting Wire, Gas and Control Settings for Aluminum With optional Spool Gun. Order part no 035 0.9 mm 030 0.8 mm225 229−E #220179#220179 #202926 OM-234 016 Spool Gun Operation On Millermatic Passport Plus Model Controls For Millermatic Passport Plus Model115/230V Weld Parameter Chart For Millermatic Passport Plus ModelAr / 2.5% CO 0350.9 mm Min/15 100 100 10/80 10/60 10/90230V 235557−ASpool Gun Operation On Renegade 180 Model Controls For Renegade 180 ModelAluminum 4043 Dcep 030 10/100 Weld Parameters For Renegade 180 Model035 10/90 Aluminum 4043 Dcep 030 10/75= Check = Change ~ = Clean = Replace Routine MaintenanceChanging Drive Rolls Turn Off power at welding power source firstChanging Push Roll Changing Lower Drive RollChanging Liner TroubleshootingBefore You Start Welding Gmaw MIG Aluminum Welding HintsWelding Techniques Direction Of WeldingGas Nozzle Contact Tip To Work Contact Tube Recessed 1/8 Common Problems/Troubleshooting− Electrical Diagrams Circuit Diagram For Millermatic 140/180 234 419-B − Parts List Optional Page Page Page Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

OM-234 016D specifications

Miller Electric OM-234 016D is a versatile and powerful machine designed for various welding applications. Known for its reliability and efficiency, this model integrates advanced technologies to cater to both professionals and hobbyists in the welding industry.

One of the standout features of the OM-234 016D is its inverter technology, which allows for a more compact and lightweight design compared to traditional welding machines. This technology not only enhances portability but also provides exceptional control over the welding process. The inverter system ensures stable arcs and precise welding performance, contributing to clean and consistent welds across different materials.

The OM-234 016D offers multiple welding modes, including TIG (Tungsten Inert Gas) and MIG (Metal Inert Gas), making it ideal for aluminum, steel, and other metals. The machine is capable of handling a wide range of thicknesses, making it suitable for various applications such as automotive repairs, fabrication, and light industrial work. The dual functionality allows welders to switch between modes effortlessly, adapting to specific project requirements with ease.

Another key characteristic of this model is its intuitive digital display, which provides real-time feedback on welding parameters such as voltage and amperage. This feature offers users greater control over their settings, enabling them to make precise adjustments on the fly. The machine also includes advanced arc stability features that minimize spatter and enhance overall weld quality.

Safety is a priority with the OM-234 016D, equipped with multiple safety features including thermal overload protection and input power monitoring. These functions safeguard the machine against potential damage and ensure optimal performance even under heavy-duty use.

Additionally, this welding machine is designed with user comfort in mind. Its ergonomic handle and compact footprint allow for easy transportation and operation in different environments. Whether working in a garage or on a job site, the OM-234 016D combines convenience with high-performance capabilities.

In summary, the Miller Electric OM-234 016D stands out as a robust option for those seeking a reliable welding solution. Its inverter technology, dual welding modes, user-friendly interface, and safety features make it an excellent choice for a wide range of welding tasks. This machine is a testament to Miller Electric’s commitment to innovation and quality in the welding industry, proving to be an invaluable asset for anyone looking to achieve professional results in their welding projects.