Miller Electric OM-234 016D manual Fire or Explosion hazard, Falling Unit can cause injury

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic- ing unit.

DUse only genuine replacement parts from the manufacturer.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can cause injury.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-234 016 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Description File Wire FeederOM-234 016D ProcessesFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLOLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-234 016 Removing MIG Gun From Welding Power Source SpecificationsTurn Off unit, and disconnect input power Connecting Spool Gun To Millermatic 140/180 ModelsOperation Polarity Changeover Terminal Block Close door Connecting Spool Gun To Millermatic 140/180Incorrect Connecting Spool Gun To Millermatic Passport PlusCorrect Connecting Spool Gun To Renegade Installing Wire Spool And Threading Welding Wire Spool Gun Operation On Millermatic 140/180 Models Controls For Millermatic 140/180 ModelsExample .030 diameter wire, welding 18 ga. material Weld Parameter Chart For Millermatic 140 Model w/Auto−SetENumber on right Slash is Wire Refer to chart below to select Voltage and Wire Speed basedExample 4 Selecting Wire, Gas and Control Settings for Aluminum With optional Spool Gun. Order part no 035 0.9 mm 030 0.8 mm#220179 #202926 #220179225 229−E OM-234 016 Spool Gun Operation On Millermatic Passport Plus Model Controls For Millermatic Passport Plus ModelAr / 2.5% CO 0350.9 mm Min/15 Weld Parameter Chart For Millermatic Passport Plus Model115/230V 235557−A 100 10/80 10/60 10/90100 230VSpool Gun Operation On Renegade 180 Model Controls For Renegade 180 ModelAluminum 4043 Dcep 030 10/75 Weld Parameters For Renegade 180 ModelAluminum 4043 Dcep 030 10/100 035 10/90= Check = Change ~ = Clean = Replace Routine MaintenanceChanging Lower Drive Roll Turn Off power at welding power source firstChanging Drive Rolls Changing Push RollChanging Liner TroubleshootingDirection Of Welding Gmaw MIG Aluminum Welding HintsBefore You Start Welding Welding TechniquesGas Nozzle Contact Tip To Work Contact Tube Recessed 1/8 Common Problems/Troubleshooting− Electrical Diagrams Circuit Diagram For Millermatic 140/180 234 419-B − Parts List Optional Page Page Page Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact

OM-234 016D specifications

Miller Electric OM-234 016D is a versatile and powerful machine designed for various welding applications. Known for its reliability and efficiency, this model integrates advanced technologies to cater to both professionals and hobbyists in the welding industry.

One of the standout features of the OM-234 016D is its inverter technology, which allows for a more compact and lightweight design compared to traditional welding machines. This technology not only enhances portability but also provides exceptional control over the welding process. The inverter system ensures stable arcs and precise welding performance, contributing to clean and consistent welds across different materials.

The OM-234 016D offers multiple welding modes, including TIG (Tungsten Inert Gas) and MIG (Metal Inert Gas), making it ideal for aluminum, steel, and other metals. The machine is capable of handling a wide range of thicknesses, making it suitable for various applications such as automotive repairs, fabrication, and light industrial work. The dual functionality allows welders to switch between modes effortlessly, adapting to specific project requirements with ease.

Another key characteristic of this model is its intuitive digital display, which provides real-time feedback on welding parameters such as voltage and amperage. This feature offers users greater control over their settings, enabling them to make precise adjustments on the fly. The machine also includes advanced arc stability features that minimize spatter and enhance overall weld quality.

Safety is a priority with the OM-234 016D, equipped with multiple safety features including thermal overload protection and input power monitoring. These functions safeguard the machine against potential damage and ensure optimal performance even under heavy-duty use.

Additionally, this welding machine is designed with user comfort in mind. Its ergonomic handle and compact footprint allow for easy transportation and operation in different environments. Whether working in a garage or on a job site, the OM-234 016D combines convenience with high-performance capabilities.

In summary, the Miller Electric OM-234 016D stands out as a robust option for those seeking a reliable welding solution. Its inverter technology, dual welding modes, user-friendly interface, and safety features make it an excellent choice for a wide range of welding tasks. This machine is a testament to Miller Electric’s commitment to innovation and quality in the welding industry, proving to be an invaluable asset for anyone looking to achieve professional results in their welding projects.
Top Page Image Contents