Simer Pumps 2.81E+01 owner manual Warranty, Retain Original Receipt For Your Records

Page 3

Warranty

3

 

 

Retain Original Receipt For Your Records

Limited Warranty

SIMER warrants to the original consumer purchaser (“Purchaser” or “You”) of its products that they are free from defects in material and workmanship for a period of twelve (12) months from the date of the original consumer purchase.

If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at SIMER’s option, subject to the terms and conditions set forth below. The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibility is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to repair or replacement of product only – Purchaser pays all removal, installation, labor, shipping, and incidental charges.

For parts or troubleshooting assistance, DO NOT return product to your retail store. Contact SIMER Customer Service at 1-800-468-7867.

Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet where it was purchased immediately after the discovery of any alleged defect. SIMER will subsequently take corrective action as promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after the warranty expires.

Warranty does not apply to products used in commercial/rental applications.

Sewage Pumps

DO NOT return a sewage pump (that has been installed) to your retail store. Contact SIMER Customer Service. Sewage pumps that have seen service and been removed carry a contamination hazard with them.

If your sewage pump has failed:

Wear rubber gloves when handling the pump;

For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;

Dispose of the pump according to local disposal ordinances.

Exceptions to the Twelve (12) Month Limited Warranty

Product

Warranty Period

 

 

BW85P, CM10, CMK, M40, M40P

90 days

 

 

2300, 2310, 2330, 2520ULST, 2943, 2955, 2956, 2957, 2960, 5023SS, A5500

2 Years

 

 

4” Submersible Well Pumps, 2945, 2958, 2975PC, 2985, 3075SS, 3983, 3984

3 Years

 

 

Pre-Charge Water System Tank, 3985, 3986, 3988, 3989

5 Years

 

 

3963, 3995, 3997

Lifetime

 

 

General Terms and Conditions

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not apply to the following: (1) acts of God; (2) products which, in SIMER’s sole judgement, have been subject to negligence, abuse, accident, misapplication, tampering, or alteration;

(3)failures due to improper installation, operation, maintenance or storage; (4) atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of recommended maximums.

This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other rights which vary from state to state.

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867 • Fax: 1-800-390-5351 • Web Site: simerpump.com

Image 3
Contents Call English . . . . . . . . . . . Pages Composer le 1 800 Llame alPages General Safety SafetyImportant Safety Instructions Electrical SafetyRetain Original Receipt For Your Records WarrantyReplacing An Old Pump InstallationWell Point Driven Point Installation Figure Cased Well Installation, 2 or Larger Casing FigureSurface Water Installation Installation for Surface Water FigureDischarge Pipe and Pressure Tank Connections Pre-Charge Tank Connection FigureStandard Tank Connection Figure Dial Type Voltage Selector Motor Switch SettingsWiring Connections ElectricalWinterizing the Pump Wiring Chart Recommended Wire and Fuse SizesPreparing to Start the Pump PrimingSymptom Possible Causes Corrective Action TroubleshootingDescription Qty Repair PartsSécurité générale SécuritéDirectives de sécurité importantes Sécurité concernant l’électricitéConserver l’original du reçu pour toute référence ultérieure GarantieInstallation de la pointe filtrante Figure Remplacement d’une ancienne pompeInstallation pour les eaux de surface Installation dans le cas d’eaux en surface FigureBranchements du tuyau de refoulement Branchement sur un réservoir préchargé FigureBranchement sur un réservoir standard Figure Réglages de l’interrupteur du moteur ÉlectricitéSélecteur de tension à cadran Connexions des filsTension Préparations avant le démarrage de la pompeAmorçage Hivérisation de la pompeSymptômes Causes probables Remèdes Diagnostic des pannesDésignation de pièces Qté Pièces de rechangeSeguridad general SeguridadInstrucciones importantes de seguridad Seguridad electricaGarantía limitada GarantíaInstalación Reemplazo de una bomba viejaInstalacion del punto del pozo punto de hincar Figura 3 Instalación para agua superficial Instalacion para agua superficial FiguraConexión para tanque estándar Figura Conexión para tanque pre-cargado FiguraConexiones de los cables Configuraciones del interruptor del motorElectricidad Selector de tensión de tipo cuadrantePreparación de la bomba para el invierno Preparación para arrancar la bomba Pozo profundo CebadoSíntoma Causas probables Acción correctiva Solución de problemasDescripción Piezas de repuesto

2.81E+01 specifications

Simer Pumps has long been a reputable name in the pump manufacturing industry, and one of their notable offerings is the Simer Pumps 2.81E+01 model. This advanced pump is designed for a variety of fluid handling applications, providing efficiency and reliability that can meet the demands of both residential and commercial environments.

One of the primary features of the Simer Pumps 2.81E+01 model is its robust construction, ensuring durability and longevity even under challenging conditions. This pump is built with high-quality materials that resist corrosion and wear, making it suitable for applications involving water, chemicals, and other fluids. The durability of the pump minimizes maintenance requirements and reduces the total cost of ownership over its operational lifespan.

Technology plays a vital role in the performance of the Simer Pumps 2.81E+01. It is equipped with a powerful motor that delivers excellent flow rates while maintaining energy efficiency. The pump design incorporates advanced hydraulic principles that optimize performance, making it capable of handling a wide range of fluid volumes without sacrificing efficiency. This ensures that users can rely on consistent performance, whether it's for irrigation, drainage, or industrial processes.

Another noteworthy characteristic of the Simer Pumps 2.81E+01 is its versatility. The pump is designed with adaptability in mind; it can be utilized in various settings, including residential basements for dewatering, agricultural applications for irrigation systems, and light industrial uses. Its multi-purpose capability makes it an attractive option for a wide array of users who require flexibility in their pumping solutions.

Furthermore, the Simer Pumps 2.81E+01 features ease of installation and operation. The user-friendly design includes straightforward connection points and clear instructions, allowing for quick setup and minimal downtime. Its maintenance-friendly design enables users to perform routine checks and necessary repairs without excessive complication.

In summary, the Simer Pumps 2.81E+01 is a robust, efficient, and versatile pumping solution that caters to various fluid handling needs. With its durable construction, powerful motor, adaptable design, and user-friendly features, it stands out as an excellent choice for both residential and commercial applications. Whether for dewatering, irrigation, or industrial use, this model delivers reliable performance that meets the demands of modern fluid management.