Sanyo CH3632, XHS3632, XHS2432, CH2432 service manual Service procedures Test Run

Page 99

4. Service procedures

(11) Test Run

(11)-1. Preparing for Test Run

Before starting the air conditioner, check the followings:

(1)Remove all loose matter from the cabinet espe- cially metal filings, bits of wire, and clips.

(2)Connect the control wiring correctly and tighten all electrical connections.

(3)Remove the protective spacer for the compressor used for transportation.

(4)Connect the power to the unit for at least 5 hours before starting the compressor. The bottom of the compressor should be warm to the touch and the crankcase heater around the feet of the compressor should be hot to the touch. For Ceiling mounted and Recessed Type indoor units, the flap(s) move(s) for one minute when the power is connected to the unit.

This is not the malfunction.

(5)Open both the wide and narrow tube service valves after air purge.

(6)Remove the transportation cardboard protection for the indoor fan.

(11)-2. Performing Test Run

Be careful since the fan will

CAUTION start when performing Test Run.

For XHS models

(1)For XHS models, the Operation Selector is located above the electrical component box inside the indoor unit. To access the Operation Selector, press the two latches of the air intake grille in the direction of the arrow to open the grille. Open the air intake grille downward. (Fig. 11-1)

(2)Set the TEST RUN switch of the SERVICING switches on the Operation Selector (housed inside the indoor unit) to the ON position. (Fig. 11-1)

(3)Press the ON/OFF operation button on the remote control unit and start the air conditioner in Cooling or Heating mode.

(4)Let the unit run for about 30 minutes and check that the unit operates normally.

(5)After the test run, be sure to set the TEST RUN switch back to the OFF position to cancel the test run mode. Then stop the air conditioner.

All OFF for

 

 

 

 

 

initial settings.

 

 

 

 

 

ON

 

 

 

 

 

OFF

 

 

 

Operation

 

 

 

 

 

1 2 3 4

1. TEST RUN(ON)

 

 

ON • I

selector

1 2 3 4

ADDRESS

SWEEP

 

 

 

OFF•O

 

 

2. PCB CHK.(ON)

1 2 3

NORM. HOLD

 

 

1. TEST RUN

3. RCU MAIN(OFF)

 

 

 

 

/ SUB(ON)

 

 

 

 

2. (OFF)

4. OFF

 

 

 

 

 

 

 

 

 

3. (OFF)

 

 

 

 

 

4. (ON)

Section

1

Air filterAir intake grille

1584_M_I

Fig. 11-1

2

3

4

SM830076

– 99 –

Page 98 Page 100
Image 99
Page 98 Page 100
Contents Split System AIR Conditioner If Necessary, Get Help Please Read Before StartingWHO should USE this Manual Table of Contents Service Procedures Introduction Read Me First Specifications Performance Specifications Unit SpecificationsData Subject to Change Without Notice Model No Indoor Unit XHS3632 Outdoor Unit PNR-XHS3632 Fan motor Specifications Major Component Specifications Indoor UnitModel No XHS3632 Source Compressor Specifications Major Component Specifications Outdoor UnitModel No CH3632 Source Model No XHS2432 Power Transformer Specifications Other Component Specifications Indoor UnitXHS3632 Power Transformer Model No CH2432 Specifications Other Component Specifications Outdoor UnitModel No CH3632 Specifications Dimensional Data Indoor Unit XHS2432 Specifications Dimensional Data Indoor Unit XHS3632 Specifications Dimensional Data Outdoor Unit CH2432Specifications Dimensional Data Outdoor Unit CH3632 Specifications Refrigerant Flow Diagram Outdoor Unit CH2432 Operating RangeIndoor Unit XHS2432 Indoor Unit XHS3632 Specifications Refrigerant Flow Diagram Outdoor Unit CH3632Processes and Functions Processes and1.SpecificationsfunctionsRoom Temperature Control Processes and functionsCooling Heating Cold Draft Prevention Heating Cycle Automatic Fan Speed Indoor Unit Chart Explanations and notesOutdoor Fan Speed Control Freeze Prevention Cooling Condensing Temperature Control Cooling This function prevents the air conditioner from overloading Overload Protection HeatingDischarge Temperature Control Cooling and Heating Auto. Mode for Automatic Heating/Cooling Switching Processes and functions Defrosting Control, Outdoor Heat Exchanger Coil Heating Time Chart for Defrosting11 4-Way Valve, Solenoid Control Normal Control ModeAuto Control Mode Automatic Restart after Power InterruptionFuzzy Control Compressor Discharge Gas TemperatureElectronic Expansion Valve Heating Except During DefrostingOverload Protection Compressor Current Detection CircuitFuzzy control optimal refrigerant flow rate control Contents and Order of controlElectronic Expansion Valve Control Refrigerant flow distribution controlVoltage Detection Control Processes and functions Electrical data Electrical DataXHS2432, XHS3632 Indoor UnitSchematic Diagram OutdoorUnit CH2432Controller Outdoor UnitCH3632 Electric Wiring DiagramFMO1 FMO2 Electrical data Service procedures Service ProceduresThis section explains TroubleshootingCheck inter-unit wiring Service procedures Check before and after TroubleshootingCheck power supply Check power supply wiringCooling Service procedures Heating Controller Display Meanings of alarm messagesWireless remote Controller Display Refrigerant Shortage Service procedures Symptoms and parts to inspect SM830076 0335MI Influenced by external noise Yes Start Is there connector contact defect? Correct the connection 0343MI Symptom LCD on the remote controller displays Check E15 Symptom LCD on the remote controller displays Check E16 0346MI Indoor fan does not operate Compressor motor does not operate Set service check switches Service procedures Use the test run procedure Service procedures Check the sensor temperature readings Find out about past service problems SET Temp Check the remote controller itself for correct operation Service procedures Execute the auto. address operation 0362MI 0364MI Change the shift temperature in heating mode Service procedures Set the indoor unit address Set the No. of R. C. which you want to set with , button 0371MI Service procedures Change the period of the filter timer Measurement of Insulation Resistance Checking the Electrical ComponentsCompressor motor thermal protector . . . . . . Outdoor unit Checking the Protective DevicesPower transformer TR1 Service procedures Checking the Electrical PartsContinuity of fuse on P.C.B. Ass’y Motor capacitor ............ Both in indoor and outdoor unitCompressor motor magnetic contactor 52C ………… Outdoor unit Case of single -phase compressorSolenoid coil of the electronic refrigerant Compressor motor CM ……… Outdoor unitCH2432 Service procedures Sensor and Solenoid Layout DiagramXHS3632 Service procedures Thermistor Characteristic Curve Standard control single outdoor unit Service procedures C.B. SettingCentral control when using the *system controller Setting of indoor control P.C.BBoth OFF Set to When shipped from factory Displaying Indoor / Outdoor Unit Combination Numbers Service procedures Automatic Address Setting MethodItems to Check Prior to Test Run Service procedures Test Run 100 Test Run Procedure CR-THS2432 Service procedures 12 P.C.B. and Parts LocationCR-CH2432 Checking procedure for each P.C.B Switch the pin from normal operation to check operation Service procedures Check PinsCentral Region
Related manuals
Manual 25 pages 43.24 Kb Manual 1 pages 11.04 Kb Manual 1 pages 11.94 Kb

XHS3632, XHS2432, CH3632, CH2432 specifications

The Sanyo CH3632 is a cutting-edge air conditioning unit that exemplifies efficiency and innovation in climate control technology. Designed primarily for residential use, this model has attracted attention due to its combination of powering performance and user-friendly features.

One of the standout characteristics of the Sanyo CH3632 is its energy efficiency. With a high Seasonal Energy Efficiency Ratio (SEER), the unit consistently delivers cooling while minimizing energy consumption. This not only reduces monthly electricity bills but also contributes positively to environmental sustainability. Its environmentally friendly refrigerant further emphasizes Sanyo's commitment to eco-conscious designs.

The unit employs advanced inverter technology, which allows for variable-speed compressor operation. This means that instead of turning on and off, the compressor adjusts its speed based on the cooling needs of the space. This creates a more stable and comfortable indoor environment while ensuring quieter operation. The reduced noise levels make the CH3632 an excellent choice for bedrooms and living spaces where peace and tranquility are essential.

Another key feature of the Sanyo CH3632 is its dual filtration system, which combines a pre-filter with a HEPA filter. This system effectively captures dust, allergens, and other airborne particulates, ensuring that the air quality remains high. Homeowners can breathe easier knowing that their indoor air is cleaner and healthier.

Smart features are also integral to this model. The Sanyo CH3632 can be integrated with smart home systems, allowing users to control temperature settings via mobile apps or voice commands. This connectivity makes it convenient to manage cooling preferences from anywhere in the house, adding a layer of modern convenience to home comfort.

Installation of the Sanyo CH3632 is straightforward and can often be completed without extensive modifications to existing structures. Its sleek design allows it to blend seamlessly into various home aesthetics, making it an attractive addition to any space.

In summary, the Sanyo CH3632 is a highly efficient air conditioning unit that incorporates advanced technologies for optimal performance. With eco-friendly features, smart connectivity, and an emphasis on air quality, it sets a high standard for comfort in residential air conditioning solutions.
Top Page Image Contents