Harbor Freight Tools 91130 To Attach The Motor Assembly, To Attach The Fence

Page 16

4.Screw a Nut (24B) downward on each of the eight Hex Screws (23B). Insert the Hex Screws downward through the eight mounting holes located on the Main Table (20B). Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.)

To Attach The Motor Assembly:

1.Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjustment Board until it sits on the eight Hex Screws (23B). (See Figures J and K.)

ADJUSTMENT BOARD (17D)

SCREW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(16D)

 

 

 

 

 

 

. .

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

. .

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAIN

 

 

 

 

 

 

 

 

 

 

TABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPINDLE

 

 

 

 

 

(20B)

 

 

 

 

 

 

 

 

 

MOTOR

 

LOCK

 

 

 

 

 

 

 

 

LEVER

 

 

 

 

 

 

 

ASSY.

 

 

 

 

 

 

 

 

 

(22E)

 

 

 

 

 

 

 

 

 

 

FIGURE K

2.NOTE: The height of the Adjustment Board (17D) can be adjusted by inserting a hex wrench (not included) through the Adjustment Board and adjusting each Hex Screw (23B) individually. Once adjusted, secure the Adjustment Board to the Main Table (20B) with four Screws (16D). (See Figures J and K.)

To Attach The Fence:

1.The Upper Fence (16C) is supplied with six Nuts (11C) already fitted to one channel (groove) of the Upper Fence. The furthest two Nuts on each end of the Upper Fence are for attaching the two Fence Supports (10C) to the Upper Fence. The middle two Nuts are for attaching the Dust Port Box (24C) to the Upper Fence. (See Assembly Diagram C.)

SKU 91130

For technical questions, please call 1-800-444-3353.

Page 16

Image 16
Contents For technical questions or replacement parts, please call Router with Full Size TableProduct Specifications General Safety RulesUnpacking Save this ManualElectrical Safety Personal SafetyTool USE and Care Service Specific Safety RulesSKU For technical questions, please call Page Page Grounding Grounded Tools Tools with Three Prong PlugsExtension Cords Double Insulated Tools Tools with TWO Prong PlugsSee Figure C, next See Figure CSymbology Figure CProduct Features Figure EAssembly Diagrams on pages 28, 29, 30, 31, Assembly InstructionsTo Assemble The Base See Figure G To Assemble The Mid-SectionFront View To Attach The Mid-Section To The Body See Figure HSee Figure I, next To Attach The Main TableSee Figure J Figure JTo Attach The Motor Assembly To Attach The FenceSee Assembly Diagram C See Assembly Diagram C and Figure LTo Attach The Dust Port Assembly And Protector To Install And Remove Collets See Assembly Diagram C and Figure MSee Figure N, next Figure N To Adjust The Depth Of Cut See Figures K and PTo Attach And Adjust The Feather Boards Figure RSee Figure S To Attach The Miter GaugeTo Adjust The Speed RPM To Adjust The Upper FenceSee Figure U To Turn On The Router Table To Operate The Router TablePlease Read the Following Carefully INSPECTION, MAINTENANCE, and CleaningDo not use damaged equipment Parts List B Parts List aParts List C Parts List D Parts List EAssembly Diagram a Assembly Diagram B Assembly Diagram C Assembly Diagram D Assembly Diagram E