Harbor Freight Tools 91130 To Attach And Adjust The Feather Boards, Figure R

Page 21

2.Fit the Adjustment Tool (27D) in the corresponding slots of the Height Adjusting Ring (14D) and turn the Ring in a clockwise direction for a deeper depth of cut or counterclockwise for a lesser depth of cut. (See Figure Q.)

3.NOTE: The Height Adjustment Ring (14D) is marked with a straight arrow point- ing to the edge of the Adjustment Board (17D). The Adjustment Board (17D) is marked with ten corresponding lines. When setting the depth of cut, always align the arrow on the Height Adjustment Ring with one of the ten lines on the Adjust- ment Board. (See Figure Q.)

4.To determine the depth of cut, use a ruler to measure the distance between the base of the Main Table (20B) and the tip of the router bit.

5.Once the depth of cut is acquired, align the Height Adjustment Lock (23D) and turn the Lock in a clockwise direction to lock. (See Figure Q.)

6.NOTE: Always make a trial cut on scrap wood to ensure the correct depth of cut has been selected.

To Attach And Adjust The Feather Boards:

1.To attach the first Feather Board (14C), slide the heads of two Square Head Screws (15C) into a channel (groove) on the front of the Upper Fence (16C). Then mount the Feather Board against the Upper Fence, and secure it with two Large Washers (7C) and two Fence Lock Knobs (8C). (See Figure R.)

UPPER FENCE (16C)

FEATHER

BOARD (14C)

 

FEATHER BOARD

FENCE

 

 

LOCK

 

 

 

 

 

(14C)

 

KNOB

 

 

 

 

 

 

 

 

SQUARE

 

 

(8C)

 

 

 

 

 

 

 

 

HEAD

 

 

 

 

 

 

 

 

SCREW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(15C)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LARGE

 

 

 

 

 

 

 

WASHER

 

 

 

 

 

 

 

(7C)

UPPER FENCE (16C)

FIGURE R

SKU 91130

For technical questions, please call 1-800-444-3353.

Page 21

Image 21
Contents Router with Full Size Table For technical questions or replacement parts, please callGeneral Safety Rules Product SpecificationsUnpacking Save this ManualPersonal Safety Electrical SafetyTool USE and Care Specific Safety Rules ServiceSKU For technical questions, please call Page Page Grounded Tools Tools with Three Prong Plugs GroundingDouble Insulated Tools Tools with TWO Prong Plugs Extension CordsSee Figure C, next See Figure CFigure C SymbologyFigure E Product FeaturesAssembly Instructions Assembly Diagrams on pages 28, 29, 30, 31,To Assemble The Base To Assemble The Mid-Section See Figure GFront View See Figure H To Attach The Mid-Section To The BodySee Figure I, next To Attach The Main TableFigure J See Figure JTo Attach The Fence To Attach The Motor AssemblySee Assembly Diagram C and Figure L See Assembly Diagram CTo Attach The Dust Port Assembly And Protector See Assembly Diagram C and Figure M To Install And Remove ColletsSee Figure N, next Figure N See Figures K and P To Adjust The Depth Of CutFigure R To Attach And Adjust The Feather BoardsTo Attach The Miter Gauge See Figure STo Adjust The Upper Fence To Adjust The Speed RPMSee Figure U To Operate The Router Table To Turn On The Router TableINSPECTION, MAINTENANCE, and Cleaning Please Read the Following CarefullyDo not use damaged equipment Parts List a Parts List BParts List C Parts List E Parts List DAssembly Diagram a Assembly Diagram B Assembly Diagram C Assembly Diagram D Assembly Diagram E