Cisco Systems PRP-2/R=, PRP-1=, PRP-2= Display LEDs, Cisco IOS System Error Messages publications

Page 15

Product Overview

The PRP-2 has the following LED indicators:

•Two Flash disk activity LEDs, one for each Flash disk slot (labeled SLOT-0 and SLOT-1)—Indicate when the Flash disk slot is accessed.

•Two Ethernet port LEDs used in conjunction with each of the three RJ-45 Ethernet connectors:

–LINK—indicates link activity

–DATA—indicates data transmission or reception

•Two BITS port LEDs used in conjunction with each of the two BITS ports:

–SIG—indicates carrier signal available

–ACT—indicates the interface is active

Display LEDs

The alphanumeric display LEDs are organized as two rows of four characters each and are located at one end of the card. These LEDs provide system status and error messages that are displayed during and after the boot process. The boot process and the content displayed are controlled by the MBus module software of the PRP.

At the end of the boot process, the LEDs are controlled by the Cisco IOS software (via the MBus), and the content displayed is designated by the Cisco IOS software.

A complete, descriptive list of all system and error messages is located in the

Cisco IOS System Error Messages publications.

The display LEDs indicate the following:

•Status of the PRP

•System error messages

•User-defined status/error messages

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			15
	OL-11656-01			15

Image 15

Contents Document Contents Important Information Router InformationSupported Platforms PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Program boot image Type Size Quantity Description LocationMB fixed Secondary CPU cache memory functions Sdram Following LEDs are used on the PRP Flash MemoryPRP LEDs Status LEDsDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchAsynchronous Serial Ports Ethernet PortsHard Disk Drive Preparing for Installation Safety GuidelinesCompact Flash Disk Preventing Electrostatic Discharge Removing and Installing a PRP Required Tools and EquipmentWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions LED Display Description Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP Cisco IOS is enabled and this PRP is in standby modeChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Prompted to abort the copy, type n SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Another disk or at another locationUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Configuring Interfaces on the PRP Configuring an Ethernet InterfaceEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionLists Ieee 802.3u physical characteristics for 100BASE-TX Parameter RJ-45Parameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerBoot Field Settings Boot Field MeaningDescribed in Table Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration RegisterAddress net host Data Transmission Rate bps9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18 GB Dimm U15GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Obtaining Documentation Cisco.comProduct Documentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsProduct Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01