Cisco Systems PRP-2/R= manual Is correct, continue with Step, Another disk or at another location

Page 35

 

 

 

 

 

 

 

 

 

 

 

 

Upgrading to the PRP

 

 

Step 4

If the Cisco IOS version is not the same as the one running on the GRPs, delete

 

 

the image from the disk using the delete disk1: filename command (or the delete

 

 

stby-disk1:filenamecommand if the Flash disk is in the standby RP). If the image

 

 

is correct, continue with Step 7.

 

 

 

 

 

 

 

Note Before you delete the image, verify that you have a copy of this image on

 

 

 

 

another disk or at another location.

 

 

 

 

 

Step 5

Use the copy tftp: disk1: command to copy onto the Flash disk a PRP image that

 

 

is the same as that currently running on the GRPs (in this example, 12.0(26)S).

 

 

PRP images are titled c12kprp-<feature set>-<compression>.120-<release id>.

 

 

You will receive an error that the PRP image is not executable on the GRP. When

 

 

prompted to abort the copy, type n.

 

 

Use the copy tftp: stby-disk1:command if the Flash disk is in the standby RP.

 

 

Router# copy tftp: disk1:

 

 

Address or name of remote host [172.16.16.254]?

 

 

Source filename [c12kprp-boot-mz.120-26.S]? c12kprp-p-mz.120-26.S

 

 

Destination filename [c12kprp-p-mz.120-26.S]?

 

 

Accessing tftp://172.16.16.254/c12kprp-p-mz.120-26.S...

 

 

%Warning: File not a valid executable for this system

 

 

Abort Copy? [confirm] n

 

Step 6

To verify that the image has been copied correctly, verify the MD5 hash for the

 

 

new image on disk1:. To do this, use the command verify /md5 disk1image-name.

 

 

The resulting string should be compared against the MD5 hash value posted on

 

 

the Software download page on Cisco.com.

 

Step 7

Place the Flash disk referred to in Step 5 back into the PRP Flash disk drive.

 

Step 8

Repeat Step 2 through Step 7 for the second PRP to be installed as standby.

 

Step 9

Remove any existing boot system commands from the running configuration by

 

 

using the command no boot system. This will make the PRP boot from the image

 

 

on the Flash disk.

 

Step 10

Remove the standby GRP from the router.

 

Step 11

Insert the PRP into the router in place of the standby GRP. The PRP will now

 

 

begin to load the Cisco IOS image contained on the Flash disk. At this stage, even

 

 

though a GRP and a PRP are in the chassis simultaneously, the router remains in

 

 

SSO or RPR+ mode because the RPs are running the same image.

 

 

 

 

Performance Route Processor Installation and Configuration Guide

 

 

 

 

 

 

 

OL-11656-01

 

 

 

 

35

 

 

 

 

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Document Contents Supported Platforms Important InformationRouter Information PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation MB fixed Secondary CPU cache memory functions Program boot imageType Size Quantity Description Location Sdram Following LEDs are used on the PRP Flash MemoryPRP LEDs Status LEDsDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchHard Disk Drive Asynchronous Serial PortsEthernet Ports Compact Flash Disk Preparing for InstallationSafety Guidelines Preventing Electrostatic Discharge Working with Electrical Equipment Removing and Installing a PRPRequired Tools and Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions LED Display Description Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP Cisco IOS is enabled and this PRP is in standby modeChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Prompted to abort the copy, type n SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Another disk or at another locationUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Ethernet Interface Receptacles, Cables, and Pinouts Configuring Interfaces on the PRPConfiguring an Ethernet Interface RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionParameter Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter RJ-45 Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerDescribed in Table Boot Field SettingsBoot Field Meaning Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration Register9600 4800 1200 2400 Address net hostData Transmission Rate bps About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB DIMMs U15 and U18 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB Dimm U15 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationFCC Class a Compliance Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Product Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackCisco Product Security Overview For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01
Top Page Image Contents