Cisco Systems PRP-2=, PRP-1=, PRP-1/R=, PRP-2/R= manual Router# dir disk1

Page 34

Upgrading to the PRP

BOOTLDR	=
Configuration register	= 0x2102
Peer Processor Information :
----------------------------
Standby Location	= slot 4
Current Software state	= STANDBY HOT
Uptime in current state	= 2 hours, 13 minutes
Image Version	= Cisco Internetwork Operating System

Software

IOS (tm) GS Software (GSR-P-M), Version 12.0(26)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac Copyright (c) 1986-2003 by cisco Systems, Inc. Compiled Mon 25-Aug-03 10:44 by nmasa

BOOT =

CONFIG_FILE = BOOTLDR =

Configuration register = 0x2102

Step 2 Remove the Flash disk from the PRP card and install it into slot 1 of the active RP. The following message will be displayed; do not format the disk.

22:21:31: %PCMCIAFS-5-DIBERR: PCMCIA disk 1 is formatted from a different router or PC. A format in this router is required before an image can be booted from this device

Note If your router is running an image prior to Cisco IOS Release 12.0(25)S2, you are advised to insert the Flash disk into slot 1 of the standby RP, and not the active RP.

Step 3 Verify the disk contents using the dir disk1: command (or the dir stby-disk1:command if the Flash disk is in the standby RP).

Router# dir disk1:

Directory of disk1:/

1 -rw- 17329392 Dec 3 2003 11:44:46 +00:00 c12kprp-p-mz.120-27.S

63832064 bytes total (46465024 bytes free)

	Performance Route Processor Installation and Configuration Guide
34	OL-11656-01

Image 34

Contents Document Contents Router Information Important InformationSupported Platforms Cisco IOS Software Requirements PRP RedundancyHardware Revision Requirements Output from a later software release would be as followsProduct Overview Related DocumentationPRP Functions Shows the front panel view of the PRP-2PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Type Size Quantity Description Location Program boot imageMB fixed Secondary CPU cache memory functions Sdram Status LEDs Flash MemoryPRP LEDs Following LEDs are used on the PRPCisco IOS System Error Messages publications Display LEDsSoft Reset Switch Flash Disk SlotsEthernet Ports Asynchronous Serial PortsHard Disk Drive Safety Guidelines Preparing for InstallationCompact Flash Disk Preventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a PRPWorking with Electrical Equipment Removing a PRP Illustrates the PRP installed in a chassis Ejector LeversShows the ejector levers in detail Installing a PRP Removing and Installing a PRP Checking the Installation PRP Boot ProcessStarting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is in standby mode Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status Upgrading to the PRP ETH BitsUpgrading to the PRP Without Rebooting the Router Router# show redundancyRouter# dir disk1 Another disk or at another location SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP With Rebooting the Router Verify the disk contents using the dir disk1 commandUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot Differentiating Between PRP-1 and PRP-2 0x10Configuring an Ethernet Interface Configuring Interfaces on the PRPEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Ethernet Port Pin Signal Description Crossover Cable Pinout for Connecting Two PRPsParameter RJ-45 Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter Ethernet Interface Cable Connection Procedure Configuring the Ethernet Interfaces Using the Ethernet Port on the PRPUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Configuring the Auxiliary Interface Signal Input/Output DescriptionUnderstanding the Software Configuration Register Description of the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Defines the bits in the software configuration register Bit Number Hexadecimal Value Meaning/FunctionBoot Field Meaning Boot Field SettingsDescribed in Table Configuring the Software Configuration Register Command PurposeBits in the Software Configuration Register Action/Filename BitData Transmission Rate bps Address net host9600 4800 1200 2400 Using Flash Disks in the PRP About Flash DisksRemoving and Installing a Flash Disk in the PRP Product NumberInstalling and Removing a Flash Disk Installing a Flash Disk Working with Flash DisksBooting from a Flash Disk Boots the named file from the Flash disk in slotRemoving and Installing a Compact Flash Disk Removing the CF from the PRP-2 BoardRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB Dimm U15 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB DIMMs U15 and U18 Removing a Dimm Cisco Product Number Dimm Modules Sdram Dimm SocketsDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Regulatory, Compliance, and Safety Information Checking the Dimm InstallationElectromagnetic Compatibility Regulatory Statements Translated Safety Warnings and Agency ApprovalsFCC Class a Compliance Canada Europe EURegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Cisco.com Obtaining DocumentationProduct Documentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation Reporting Security Problems in Cisco Products For emergencies only security-alert@cisco.comObtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01