Cisco Systems PRP-1/R=, PRP-1=, PRP-2=, PRP-2/R= manual Checking the Installation

Page 29

Checking the Installation

Step 4 During the line card boot process, which occurs immediately after the PRP boots, observe the alphanumeric display LEDs on each line card.

The system attempts to boot identical line cards in parallel. Furthermore, the system boots line cards as soon as they are powered on and become available for a system boot. The physical location of the alphanumeric display LEDs on the line cards is the same as on the PRP, which is shown in Figure 7.

See the appropriate line card installation and configuration note for complete details on line card display LED sequences.

You must meet the following criteria to successfully boot the PRP:

•Flash disk is installed in Flash disk slot 0

•Flash disk contains a valid Cisco IOS software image

•Software configuration register is set to 0x2102

The system automatically boots this Cisco IOS software image. The system then enters the setup facility, where you are prompted to perform a basic configuration of the system.

Otherwise, the system enters the ROM monitor and the appropriate prompt appears (Rommon>).

Step 5 If the ROM monitor prompt (Rommon>) appears, you must boot the Cisco IOS software image you want to use by entering the appropriate b command at the ROM monitor prompt:

•b—Boots the default system software from onboard Flash memory (if it is present in onboard Flash memory)

•b filename [host]—Boots the file filename from the server host using TFTP

•b flash—Boots the first file in the Flash memory card in Flash card slot 0

Caution To prevent system problems, use the b flash command option carefully; otherwise, you might instruct the system to boot a non-Cisco IOS software image from Flash memory. This command is not used with Flash disks.

•b slot0: filename—Boots the file filename from the Flash memory card in Flash card slot 0

•b slot1: filename—Boots the file filename from the Flash memory card in Flash card slot 1

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			29
	OL-11656-01			29

Image 29

Contents Document Contents Supported Platforms Important InformationRouter Information PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation MB fixed Secondary CPU cache memory functions Program boot imageType Size Quantity Description Location Sdram PRP LEDs Flash MemoryStatus LEDs Following LEDs are used on the PRPDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchHard Disk Drive Asynchronous Serial PortsEthernet Ports Compact Flash Disk Preparing for InstallationSafety Guidelines Preventing Electrostatic Discharge Working with Electrical Equipment Removing and Installing a PRPRequired Tools and Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is the active PRP Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is in standby mode LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Is correct, continue with Step SSO or RPR+ mode because the RPs are running the same imageAnother disk or at another location Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Ethernet Interface Receptacles, Cables, and Pinouts Configuring Interfaces on the PRPConfiguring an Ethernet Interface RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionParameter Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter RJ-45 Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerDescribed in Table Boot Field SettingsBoot Field Meaning Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration Register9600 4800 1200 2400 Address net hostData Transmission Rate bps About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB DIMMs U15 and U18 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB Dimm U15 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationFCC Class a Compliance Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Product Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackCisco Product Security Overview For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01