Cisco Systems PRP-1/R=, PRP-1=, PRP-2= Documentation Feedback, Cisco Product Security Overview

Page 85

Documentation Feedback

Ordering Documentation

You must be a registered Cisco.com user to access Cisco Marketplace. Registered users may order Cisco documentation at the Product Documentation Store at this URL:

http://www.cisco.com/go/marketplace/docstore

If you do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Documentation Feedback

You can provide feedback about Cisco technical documentation on the

Cisco Technical Support & Documentation site area by entering your comments in the feedback form available in every online document.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.ht ml

From this site, you will find information about how to do the following:

Report security vulnerabilities in Cisco products

Obtain assistance with security incidents that involve Cisco products

Register to receive security information from Cisco

A current list of security advisories, security notices, and security responses for Cisco products is available at this URL:

http://www.cisco.com/go/psirt

 

 

Performance Route Processor Installation and Configuration Guide

 

 

 

 

 

 

OL-11656-01

 

 

85

 

 

 

Image 85
Contents Document Contents Router Information Important InformationSupported Platforms PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Type Size Quantity Description Location Program boot imageMB fixed Secondary CPU cache memory functions Sdram PRP LEDs Flash MemoryStatus LEDs Following LEDs are used on the PRPDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchEthernet Ports Asynchronous Serial PortsHard Disk Drive Safety Guidelines Preparing for InstallationCompact Flash Disk Preventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a PRPWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is the active PRP Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is in standby mode LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Is correct, continue with Step SSO or RPR+ mode because the RPs are running the same imageAnother disk or at another location Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Configuring an Ethernet Interface Configuring Interfaces on the PRPEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionParameter RJ-45 Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerBoot Field Meaning Boot Field SettingsDescribed in Table Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration RegisterData Transmission Rate bps Address net host9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB Dimm U15 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationElectromagnetic Compatibility Regulatory Statements Translated Safety Warnings and Agency ApprovalsFCC Class a Compliance Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Cisco.com Obtaining DocumentationProduct Documentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01