Cisco Systems PRP-1/R=, PRP-1=, PRP-2=, PRP-2/R= manual Upgrading to the PRP

Page 41

Upgrading to the PRP

Step 7 Make a note of the image name that is being used on the PRP. You can use the command dir disk1:.

Step 8 Set the boot system command to boot the new IOS image. Note that the reference will be against disk0:. This is deliberate. Use the command boot system flash disk0: PRP-image-name.

Step 9 Save the running configuration to disk1: by using the command copy running-config disk1: config-name. You can check the configuration by using the command more disk1: config-name.

Note Do not save the configuration on the GRP. In other words, do not type copy running-configstartup-configor write memory. Not saving the configuration ensures that the GRP maintains its original configuration, which will enable you to reinstall the GRP in the future if necessary.

Step 10 Confirm that disk1 now contains the IOS image and configuration by using the command dir disk1:. The Cisco IOS image needs to be the first image on the disk.

Step 11 Turn off the router.

Step 12 Remove the GRP and insert the PRP in its place.

Step 13 Connect the Ethernet and console cables to the PRP.

Step 14 Remove the Flash disk from slot1: on the GRP and insert the Flash disk into slot0: on the PRP.

Step 15 Boot the router.

Step 16 The router will come up with no configuration and prompt you to enter the Initial Configuration menu. Abort the Initial Configuration options by entering no when prompted.

Step 17 Copy the configuration file which is stored on disk0: to the startup-configuration on the PRP by using the command copy disk0: config-namestartup-config.

Note Do not copy the configuration file to the running configuration.

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			41
	OL-11656-01			41

Image 41

Contents Document Contents Supported Platforms Important InformationRouter Information PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation MB fixed Secondary CPU cache memory functions Program boot imageType Size Quantity Description Location Sdram PRP LEDs Flash MemoryStatus LEDs Following LEDs are used on the PRPDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchHard Disk Drive Asynchronous Serial PortsEthernet Ports Compact Flash Disk Preparing for InstallationSafety Guidelines Preventing Electrostatic Discharge Working with Electrical Equipment Removing and Installing a PRPRequired Tools and Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is the active PRP Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is in standby mode LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Is correct, continue with Step SSO or RPR+ mode because the RPs are running the same imageAnother disk or at another location Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Ethernet Interface Receptacles, Cables, and Pinouts Configuring Interfaces on the PRPConfiguring an Ethernet Interface RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionParameter Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter RJ-45 Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerDescribed in Table Boot Field SettingsBoot Field Meaning Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration Register9600 4800 1200 2400 Address net hostData Transmission Rate bps About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB DIMMs U15 and U18 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB Dimm U15 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationFCC Class a Compliance Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Product Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackCisco Product Security Overview For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01